TF536 Rev 2 Design Complete (all gone)

Post by **8 Bit Dreams** » 28 Apr 2020 13:45

Ok, will do it and report here :)

EDIT:
Ok, tried to pull pin1 high, amiga boots but ide isn't working,
Pulling pin1 low doesn't allow card to work, power led remains dimmed...

Post by **terriblefire** » 29 Apr 2020 10:34

8 Bit Dreams wrote: 28 Apr 2020 13:45 Ok, will do it and report here :)

EDIT:
Ok, tried to pull pin1 high, amiga boots but ide isn't working,
Pulling pin1 low doesn't allow card to work, power led remains dimmed...

Did you make sure to lift the pin off the pad? otherwise you short IOR high.

Yes if you set it low then its not gonna boot thinking about it.. Just to be sure this is pin 1....

pin1.JPG

Post by **terriblefire** » 29 Apr 2020 22:57

8 Bit Dreams wrote: 29 Apr 2020 22:17 Yes, Pin1 is lifted and connected to Pin8.. :?

Sorry no just lift it and connect it to pin 2. Sorry if the Diagram is misleading.

Subzero79 · Post by **Subzero79** » 30 Apr 2020 14:00

Today recieved parts from mouser ,pcb not arrived yet
Ordered some goof flux and kester solder wire

PaulJ_2.0 · Post by **PaulJ_2.0** » 30 Apr 2020 17:05

terriblefire wrote: 29 Apr 2020 22:57 Sorry no just lift it and connect it to pin 2. Sorry if the Diagram is misleading.

Aren't pin1 and pin2 connected?

Post by **terriblefire** » 30 Apr 2020 17:09

PaulJ_2.0 wrote: 30 Apr 2020 17:05
terriblefire wrote: 29 Apr 2020 22:57 Sorry no just lift it and connect it to pin 2. Sorry if the Diagram is misleading.
Aren't pin1 and pin2 connected?

No thats my corrected schematic... ignore the picture except for orientation.

PaulJ_2.0 · Post by **PaulJ_2.0** » 30 Apr 2020 17:14

terriblefire wrote: 30 Apr 2020 17:09 No thats my corrected schematic... ignore the picture except for orientation.

Ah!

As you were then Sir :)

Post by **terriblefire** » 30 Apr 2020 17:21

PaulJ_2.0 wrote: 30 Apr 2020 17:14 As you were then Sir :)

Its very confusing but lift pin 1 and attach it to pin 2 and nothing else. Essentially DIR pin should not be attached to IOR, That was a mistake.

Post by **8 Bit Dreams** » 01 May 2020 11:37

Ok here is my update:
done like Stephen said (lifted Pin1 and connected it to Pin2) - card is fully working now!
Thumbs up!🖒🖒

Subzero79 · Post by **Subzero79** » 01 May 2020 11:43

u removed all rns underside the ide and polulate ics? plus lift pin 1 and tie to high
?

exxos's Atari, Amiga & retro forum

TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Re: TF536 Rev 2 Design Complete (all gone)

Who is online