First look at the new board
REMINDER - Stay logged in for at least 2 hours a week to get whitelisted.
Also it helps build a picture where our "good traffic" is coming from for detection scripts.
:o)
Also it helps build a picture where our "good traffic" is coming from for detection scripts.
:o)
The TF330 is here
Moderators: terriblefire, Terriblefire Moderator
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
The TF330 is here
You do not have the required permissions to view the files attached to this post.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
supaduper
- Site sponsor
- Posts: 664
- Joined: 08 Nov 2018 12:05
Re: The TF330 is here
They look great Steve and a +1 for the packaging by JLC :)
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: The TF330 is here
A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
You do not have the required permissions to view the files attached to this post.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: The TF330 is here
Perfect box for sending 328s to you in :)
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
exxos
- Site Admin
- Posts: 28555
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: The TF330 is here
wow! The last boards I got were from JLC.. will see if I can check quality on one later..terriblefire wrote: 19 Nov 2018 18:41 A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
-
exxos
- Site Admin
- Posts: 28555
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: The TF330 is here
Mine isn't perfect, but not as bad as yours I think..
You do not have the required permissions to view the files attached to this post.
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: The TF330 is here
Judging by this.. Its the drill holes that are the problem. SMD pads are fine. in the next revision i'll tighten the trace to trace and give more clearance to the drill point. Probably trace to trace 6.5mil and Trace to pad 8mil.exxos wrote: 19 Nov 2018 18:50wow! The last boards I got were from JLC.. will see if I can check quality on one later..terriblefire wrote: 19 Nov 2018 18:41 A little bit concerned about the process here. I think my choice to use a 7 mi clearance was wise... they only just managed it
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
exxos
- Site Admin
- Posts: 28555
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: The TF330 is here
The 0.8mm holes look ok on my board, looks like the smaller drill holes are running out..terriblefire wrote: 19 Nov 2018 19:06 Judging by this.. Its the drill holes that are the problem. SMD pads are fine. in the next revision i'll tighten the trace to trace and give more clearance to the drill point. Probably trace to trace 6.5mil and Trace to pad 8mil.
Might be worth reporting a quality problem to them ?
-
alenppc
- Moderator Team
- Posts: 934
- Joined: 08 Nov 2018 12:59
Re: The TF330 is here
That board looks a bit thick... I hope it's just the picture, as 1.6 mm won't fit in the riser
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: The TF330 is here
Its 1.6mm. All my TF328s have been that. They fit no issue.alenppc wrote: 19 Nov 2018 19:59 That board looks a bit thick... I hope it's just the picture, as 1.6 mm won't fit in the riser
EDIT: Although i will say they were supposed to do bevelled edges and they didnt.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Who is online
Users browsing this forum: ClaudeBot and 1 guest