Woah, that's odd. Shouldn't be any heat problem on the CPLD or RAM chip -- it ran happily here for hours. Your processor says 16MHz. D'ya reckon it's marginal?
BW
Can all registered uses please login, even just for a few minutes..
It helps build a picture where our "good traffic" is coming from..
Thanks :)
It helps build a picture where our "good traffic" is coming from..
Thanks :)
DSTB1 exxos first tests & experimental firmware.
Re: DSTB1 exxos first tests.
BW
DFB1 Open source 50MHz 030 and TT-RAM accelerator for the Falcon
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Re: DSTB1 exxos first tests.
I think it is likely to be the CPU. It has been kicking around my desk for ages. I got some new ones in a tube *somewhere* . But probably won't have time now to go look for them now, but will do MondayBadwolf wrote: Fri Apr 22, 2022 7:47 pm Woah, that's odd. Shouldn't be any heat problem on the CPLD or RAM chip -- it ran happily here for hours. Your processor says 16MHz. D'ya reckon it's marginal?
*somewhere* I have some HC DIP CPUs...
Re: DSTB1 exxos first tests.
*cough* 33MHz hack *cough*
BW
DFB1 Open source 50MHz 030 and TT-RAM accelerator for the Falcon
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Re: DSTB1 exxos first tests.
*cough* PLCC68 socket *cough*
Well it has passed the "inserting it by one pin offset and powering it up test". It still works!
I have had it running with a small fan blowing on the thing for the past couple of hours and it seems fine..
Re: DSTB1 exxos first tests.
Well this was meant to have the dual purpose of an 'external' AltRAM board so the form factor was the decider for the DIP64.exxos wrote: Fri Apr 22, 2022 9:50 pm*cough* PLCC68 socket *cough*
Well it has passed the "inserting it by one pin offset and powering it up test". It still works!
I have had it running with a small fan blowing on the thing for the past couple of hours and it seems fine..
Mind you, putting a PLCC68 socket on it would make it the direct reverse of the STE adapter board which has its own perverse attraction
BW
DFB1 Open source 50MHz 030 and TT-RAM accelerator for the Falcon
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Re: DSTB1 exxos first tests.
OOPS...
- IMG_0515.JPG (377.87 KiB) Viewed 2027 times
- IMG_0516.JPG (233.76 KiB) Viewed 2027 times
- IMG_0517.JPG (355.13 KiB) Viewed 2027 times
Re: DSTB1 exxos first tests.
DFB1 Open source 50MHz 030 and TT-RAM accelerator for the Falcon
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Re: DSTB1 exxos first tests.
With blitter @Badwolf
- IMG_0518.JPG (321.37 KiB) Viewed 2007 times
Re: DSTB1 exxos first tests.
DFB1 Open source 50MHz 030 and TT-RAM accelerator for the Falcon
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Smalliermouse ST-optimised USB mouse adapter based on SmallyMouse2
FrontBench The Frontier: Elite 2 intro as a benchmark
Re: DSTB1 exxos first tests.
Will do some more tests than see if anything out of the ordinary happens...
LED working as well