Before i order the rev 1 I want to quickly look at adding a header for a fan.
We need to use 12V so it will need to be close to the edge connector.
What header component should I use?
EDIT: Is Molex KK 3 pin still the standard? https://uk.rs-online.com/web/p/pcb-headers/1707102/
REMINDER - Stay logged in for at least 2 hours a week to get whitelisted.
Also it helps build a picture where our "good traffic" is coming from for detection scripts.
:o)
Also it helps build a picture where our "good traffic" is coming from for detection scripts.
:o)
TF360 Fan Header
Moderators: terriblefire, Terriblefire Moderator
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
TF360 Fan Header
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
supaduper
- Site sponsor
- Posts: 664
- Joined: 08 Nov 2018 12:05
Re: TF360 Fan Header
two or three pin are the most used it seems on cooling fans, obviously three pin has the extra signal pin for fan speed measuring, I would still go for the three pin as options are always good and you can always hack a two pin to fit :)
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF360 Fan Header
Ok here is the dilema.. the only place left to fit this is in the top left of the board. But to do that i need to bring 12V right across the board... I... i dont wanna.supaduper wrote: 15 Sep 2019 10:15 two or three pin are the most used it seems on cooling fans, obviously three pin has the extra signal pin for fan speed measuring, I would still go for the three pin as options are always good and you can always hack a two pin to fit :)
Is 5V fan header useless?
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
supaduper
- Site sponsor
- Posts: 664
- Joined: 08 Nov 2018 12:05
Re: TF360 Fan Header
Why bother adding that , you will have a spare 5v and GND from the power reg circuit so it just means cutting and adding a couple of connectors onto the cable, what do you think ?
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF360 Fan Header
Yeah more or less what I’m thinking
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
kludge
- Posts: 400
- Joined: 08 Nov 2018 14:05
- Location: Sweden
Re: TF360 Fan Header
terriblefire wrote: 15 Sep 2019 09:57 Before i order the rev 1 I want to quickly look at adding a header for a fan.
Remember: #SiliconNotSilicone
A kludge is a workaround or quick-and-dirty solution that is clumsy, inelegant, inefficient, difficult to extend and hard to maintain.
My lack of focus:
[ 8 * A500 ][ 2 * A500+ ][ 2 * A600 ][ 2 * A1200 ][ 2 * A2000 w/ A2386 ][ A4000 w/ TF4060, CyberVision 64 3D, FastLane SCSI Z3 ][ CD32 ][ VIC-20 ][ 4 * C64 Breadbin ][ 5 * C64C ][ 2 * C128 ][ C128D ][ C64 DTV ][ 3 * Mac Classics of different types ]
My lack of focus:
[ 8 * A500 ][ 2 * A500+ ][ 2 * A600 ][ 2 * A1200 ][ 2 * A2000 w/ A2386 ][ A4000 w/ TF4060, CyberVision 64 3D, FastLane SCSI Z3 ][ CD32 ][ VIC-20 ][ 4 * C64 Breadbin ][ 5 * C64C ][ 2 * C128 ][ C128D ][ C64 DTV ][ 3 * Mac Classics of different types ]
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF360 Fan Header
Went for a 3 pin .1 header with 5V in the center and ground on each side.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
sugar
- Posts: 77
- Joined: 20 Apr 2019 22:28
Re: TF360 Fan Header
Is the fan limiting option based on limiting current supplied to the fan or am I missing something? Would love to get the fan noise down a bit.terriblefire wrote: 15 Sep 2019 13:45 Went for a 3 pin .1 header with 5V in the center and ground on each side.
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF360 Fan Header
There is no fan speed regulation on the 360.. no space to do it. Its just a 5v header.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
sugar
- Posts: 77
- Joined: 20 Apr 2019 22:28
Re: TF360 Fan Header
Cheers, need to play with some resistors then I guess.terriblefire wrote: 08 Jul 2020 00:02 There is no fan speed regulation on the 360.. no space to do it. Its just a 5v header.
Who is online
Users browsing this forum: ClaudeBot and 4 guests