New board just posted with the board house
TF536 is a port of the TF330 to the Amiga 500/Atari ST.
Specs: 68030 @ 50Mhz (fixed) frequency, 64Mb of RAM & 44Pin IDE.
You will not be able to post if you are still using Microsoft email addresses such as Hotmail etc
See here for more information viewtopic.php?f=20&t=7296
See here for more information viewtopic.php?f=20&t=7296
BOOKMARK THIS PAGE !
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
DO NOT USE MOBILE / CGNAT DEVICES WHERE THE IP CHANGES CONSTANTLY!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
New Board TF536
Moderators: terriblefire, Terriblefire Moderator
-
terriblefire
- Admin sponsor
- Posts: 5685
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
New Board TF536
You do not have the required permissions to view the files attached to this post.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
project23
- Posts: 28
- Joined: 15 May 2019 20:54
Re: New Board TF536
Holy sh*t! Well done! Hahaha
John
EDIT: This will probably be asked - is it the same BOM as the 330?
John
EDIT: This will probably be asked - is it the same BOM as the 330?
-
terriblefire
- Admin sponsor
- Posts: 5685
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: New Board TF536
The BOM isnt identical because the number of parts is different but the components used are the same ones.
There are 6 Bus buffers for example rather than 4 on the TF330 etc. This is to accomadate the INT2 feature.
EDIT: Actually I dont know yet if the CPLD will be the XC95144 or the XC95288... will see how i go when i get to the firmware stage.
There are 6 Bus buffers for example rather than 4 on the TF330 etc. This is to accomadate the INT2 feature.
EDIT: Actually I dont know yet if the CPLD will be the XC95144 or the XC95288... will see how i go when i get to the firmware stage.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
PhilC
- Moderator
- Posts: 7420
- Joined: 23 Mar 2018 20:22
Re: New Board TF536
Looks good to me.
Will support by buying a couple of boards when they are available.
Will support by buying a couple of boards when they are available.
If it ain't broke, test it to Destruction.
-
project23
- Posts: 28
- Joined: 15 May 2019 20:54
Re: New Board TF536
Yeah I'd also like to buy a couple boards if possible. I can send payment whenever ya ready to sell (assuming this is a production run you'll be selling).
John
John
-
terriblefire
- Admin sponsor
- Posts: 5685
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: New Board TF536
I'll be going down the usual route of testing myself, extending the test to the beta testers and then making it more widely available.
This card has been on my todo list for a few months and it was the reason i wasnt that keen to release the TF534 (and why i got so cross with people asking if they can upgrade the TF534.. you cant).... This card should work way better than any previous TF5xx card and have more RAM. I've dropped the FPU because its more hassle than its worth.
This card has been on my todo list for a few months and it was the reason i wasnt that keen to release the TF534 (and why i got so cross with people asking if they can upgrade the TF534.. you cant).... This card should work way better than any previous TF5xx card and have more RAM. I've dropped the FPU because its more hassle than its worth.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
project23
- Posts: 28
- Joined: 15 May 2019 20:54
Re: New Board TF536
Yeah agreed re the FPU. I haven't bothered adding mine to the 530 because I don't want to rock the boat too much on an already stable card.
Im keen to get involved at whatever stage you're comfortable with. This new card will be well worth the wait!
John
Im keen to get involved at whatever stage you're comfortable with. This new card will be well worth the wait!
John
-
Justme14
- Posts: 39
- Joined: 18 Dec 2018 21:28
- Location: Netherlands
Re: New Board TF536
:shock: that's an Awesome Board,
Seems your where busy ,designing .
Eager to see this board gets to the first boot on your Youtube channel ... ;)
I Sure will buy some boards when it's ready
Seems your where busy ,designing .
Eager to see this board gets to the first boot on your Youtube channel ... ;)
I Sure will buy some boards when it's ready
-
terriblefire
- Admin sponsor
- Posts: 5685
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: New Board TF536
literally took me 6 hours to do this board from scratch.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
PhilC
- Moderator
- Posts: 7420
- Joined: 23 Mar 2018 20:22
Re: New Board TF536
It does look like it will be much easier to assemble than the TF534, which is another bonus.
Will look into the costs when the BOM is ready.
BTW, whatever happened with that Atati and A1000 rom board?
If it ain't broke, test it to Destruction.
Who is online
Users browsing this forum: CCBot and 2 guests