Hi Stephen,
Do you have any update / eta on the planned release of the Gerber files for the TF534?
Cheers.
You will not be able to post if you are still using Microsoft email addresses such as Hotmail etc
See here for more information viewtopic.php?f=20&t=7296
See here for more information viewtopic.php?f=20&t=7296
BOOKMARK THIS PAGE !
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
DO NOT USE MOBILE / CGNAT DEVICES WHERE THE IP CHANGES CONSTANTLY!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
TF 534 Status Update
Moderators: terriblefire, Terriblefire Moderator
-
terriblefire
- Admin sponsor
- Posts: 5678
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF 534 Status Update
My life is manic right now. Not had a haircut in 6 months and just had work contracts extended for way longer than I wanted + others queuing up for other contracts... mad.go0se wrote: 25 Nov 2018 20:11 Hi Stephen,
Do you have any update / eta on the planned release of the Gerber files for the TF534?
Cheers.
As soon as i can find the time to get some TF534 gerbers cut i'll do it. I need to make sure you guys dont get cup holders made from them though.. thats whats holding me back.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
go0se
- Posts: 411
- Joined: 25 Nov 2018 19:55
Re: TF 534 Status Update
Thanks for the reply and info Stephen,
The lack of haircut tells me that you've definitely got your priorities right! :)
Cheers.
The lack of haircut tells me that you've definitely got your priorities right! :)
Cheers.
-
terriblefire
- Admin sponsor
- Posts: 5678
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF 534 Status Update
Expect something this weekend.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
8 Bit Dreams
- Moderator Team
- Posts: 785
- Joined: 09 Nov 2018 07:12
- Location: Germany
Re: TF 534 Status Update
Excited!
Got a lot Emails already
Retro computer hardware & repair in Germany
-
terriblefire
- Admin sponsor
- Posts: 5678
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF 534 Status Update
Update: I'm leaning towards cancelling the TF534 entirely for various reasons. There will be a board to replace it but its not going to be available until Q2 2019 i dont think.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
alenppc
- Moderator Team
- Posts: 932
- Joined: 08 Nov 2018 12:59
Re: TF 534 Status Update
Any chance I could get a few PCBs for my own projects? Personally I am a fan of the 534.
-
terriblefire
- Admin sponsor
- Posts: 5678
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF 534 Status Update
I have changed my mind again. I spent yesterday looking at what the next 500 board would be.. and its not something i can get my head round in terms of layout easily.. A BIG change is needed to put SDRAM on the TF534 and to make it clock switch.
So I'll push on and see if i can figure out this bus grant stuff.
My only planned changes for the TF534 at this stage are to wire up A7, A9, A10 and A11.
So I'll push on and see if i can figure out this bus grant stuff.
My only planned changes for the TF534 at this stage are to wire up A7, A9, A10 and A11.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
terriblefire
- Admin sponsor
- Posts: 5678
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: TF 534 Status Update
OK update.
I have fixed the Atari ST bus grant issue (i think).
I also have sorted a few things that i think will cause issues on the A2000. Pull up on BG20. As well as that I have cleaned up the board dramatically and ditched the pretense at dual 2 and 4 layer. Its now a 4 layer board.
I've wired up the missing address lines to the RAM CPLD and generally cleaned up the board. An order has been placed with JLCPCBs. Slow postage for cheapness and so it doesnt arrive at the same time as the TF330.
Same as the TF330 i'll post out boards each to Victor and AlenPPC when it arrives.
I have fixed the Atari ST bus grant issue (i think).
I also have sorted a few things that i think will cause issues on the A2000. Pull up on BG20. As well as that I have cleaned up the board dramatically and ditched the pretense at dual 2 and 4 layer. Its now a 4 layer board.
I've wired up the missing address lines to the RAM CPLD and generally cleaned up the board. An order has been placed with JLCPCBs. Slow postage for cheapness and so it doesnt arrive at the same time as the TF330.
Same as the TF330 i'll post out boards each to Victor and AlenPPC when it arrives.
You do not have the required permissions to view the files attached to this post.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
exxos
- Site Admin
- Posts: 27948
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: TF 534 Status Update
Georgeous :thumbup:
Who is online
Users browsing this forum: CCBot and 2 guests