Board went together without a hitch. Works perfectly fine on an A1000 with last posted firmware, tested Frontier on loop and various WHDLoad games with no issue.
Thanks!
You will not be able to post if you are still using Microsoft email addresses such as Hotmail etc
See here for more information viewtopic.php?f=20&t=7296
See here for more information viewtopic.php?f=20&t=7296
BOOKMARK THIS PAGE !
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
DO NOT USE MOBILE / CGNAT DEVICES WHERE THE IP CHANGES CONSTANTLY!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
Limited TF536 Run - Sort of Sales (All gone)
Moderators: terriblefire, Terriblefire Moderator
-
EzdineG
- Posts: 68
- Joined: 12 Nov 2018 17:19
Re: Limited TF536 Run - Sort of Sales (All gone)
Thanks!
-
mattymuc
- Posts: 12
- Joined: 02 Jan 2020 11:40
Re: Limited TF536 Run - Sort of Sales (All gone)
I have tried different CF adapters, from cheap Chinese ones to expensive ones.go0se wrote: 24 Jan 2020 22:25 Can you post close up photos of your CF adapter. Both sides if possible.
That's not the problem.
This is the adapter I built into my Amy case:
The CPLD gets 55 degrees C, which can be felt very well with the finger.
But it seems to be no problem, the card runs very stable. The maximum I
can get out is 2.4MB IDE speed.
You do not have the required permissions to view the files attached to this post.
-
terriblefire
- Admin sponsor
- Posts: 5683
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: Limited TF536 Run - Sort of Sales (All gone)
Recovering from my Peat n Diesel hangover....
I'd say between 2mb/s and 3mb/s is probably what ive got out of these devices.
I've never fully understood why some builds are better than others. Probably some marginal setup time somewhere.
I'd say between 2mb/s and 3mb/s is probably what ive got out of these devices.
I've never fully understood why some builds are better than others. Probably some marginal setup time somewhere.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
alenppc
- Moderator Team
- Posts: 932
- Joined: 08 Nov 2018 12:59
Re: Limited TF536 Run - Sort of Sales (All gone)
That’s very strange. Mine doesn’t really get any warmer than body temp, you can’t really feel anything with your finger...mattymuc wrote: 26 Jan 2020 09:22 The CPLD gets 55 degrees C, which can be felt very well with the finger.
-
terriblefire
- Admin sponsor
- Posts: 5683
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: Limited TF536 Run - Sort of Sales (All gone)
Think i need some weak pull ups on some of the address bus.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
PaulJ_2.0
- Posts: 571
- Joined: 11 May 2019 23:32
Re: Limited TF536 Run - Sort of Sales (All gone)
My CPLD doesn't get at all warm and I get 2.5Mb/Sec disk speed on both SD and CF adapters.
Today I have been running Whdload FA/18 interceptor on demo loop for 4 hours and not a single problem. CPU is nice and cool too.
Usually this game gives me crap on my TF534 and UAE so it's nice to see it being stable for once.
Today I have been running Whdload FA/18 interceptor on demo loop for 4 hours and not a single problem. CPU is nice and cool too.
Usually this game gives me crap on my TF534 and UAE so it's nice to see it being stable for once.
-
mattymuc
- Posts: 12
- Joined: 02 Jan 2020 11:40
Re: Limited TF536 Run - Sort of Sales (All gone)
Perhaps I got a fake CPLD... Who cares... If it breaks, I just solder another CPLD on the board :-)
-
terriblefire
- Admin sponsor
- Posts: 5683
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: Limited TF536 Run - Sort of Sales (All gone)
I've already said.. its because there are floating pins.
https://electronics.stackexchange.com/q ... c-get-warm
https://electronics.stackexchange.com/q ... c-get-warm
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
arkadiusz.makarenko
- Moderator Team
- Posts: 1366
- Joined: 19 Jun 2019 07:36
- Location: Edinburgh
Re: Limited TF536 Run - Sort of Sales (All gone)
My TF536 is stable under Diagrom.
I am still troubleshooting build.
Forgot that 4 layer board are pain to solder correctly. I really need to invest in better soldering station.
I am still troubleshooting build.
Forgot that 4 layer board are pain to solder correctly. I really need to invest in better soldering station.
Do not trust people. They are capable of greatness.
~ Stanislaw Lem
~ Stanislaw Lem
-
terriblefire
- Admin sponsor
- Posts: 5683
- Joined: 28 Aug 2017 22:56
- Location: Glasgow, UK
Re: Limited TF536 Run - Sort of Sales (All gone)
Yeah you really need a basic temperature controlled iron and always use the "proper" amount of fluxarkadiusz.makarenko wrote: 28 Jan 2020 21:07 My TF536 is stable under Diagrom.
I am still troubleshooting build.
Forgot that 4 layer board are pain to solder correctly. I really need to invest in better soldering station.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Who is online
Users browsing this forum: CCBot and 5 guests