I listed some here already... https://www.exxosforum.co.uk/forum/viewt ... 011#p24044derkom wrote: 25 Nov 2019 19:27 I've been wondering about that. I'm still a ways off, but it has occurred to me that I can't even try to boot the thing because I don't know what most of the jumpers do. :)
derkom's attempt
-
exxos
- Site Admin
- Posts: 28361
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: derkom's attempt
-
derkom
- Moderator
- Posts: 1231
- Joined: 29 Jul 2018 18:45
Re: derkom's attempt
BGACK pullup fix
You do not have the required permissions to view the files attached to this post.
-
Icky
- Site Admin
- Posts: 4375
- Joined: 03 Sep 2017 10:57
- Location: UK
Re: derkom's attempt
@derkom - your soldering is way neater than mine :)
-
derkom
- Moderator
- Posts: 1231
- Joined: 29 Jul 2018 18:45
Re: derkom's attempt
I probably just have a worse case of OCD. :lol:
-
derkom
- Moderator
- Posts: 1231
- Joined: 29 Jul 2018 18:45
Re: derkom's attempt
Resistor networks in (minus any more @exxos forgot :lol:), SIMM socket in (planning to try both memory setups), most ports in (I'll probably not install the DB19 until verifying this can boot), reset switch in.
No real surprises or challenges this time. I already knew the reset switch was going to be a little wonky (it was actually the first thing I checked when I got the board), but it can go in with a little "encouragement". :)
You do not have the required permissions to view the files attached to this post.
-
exxos
- Site Admin
- Posts: 28361
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: derkom's attempt
:bravo:
Well one resistor so far isn't bad I think :lol:
Yeah, stupid datasheets :roll:derkom wrote: 26 Nov 2019 20:18 I already knew the reset switch was going to be a little wonky (it was actually the first thing I checked when I got the board), but it can go in with a little "encouragement". :)
-
Icky
- Site Admin
- Posts: 4375
- Joined: 03 Sep 2017 10:57
- Location: UK
Re: derkom's attempt
Great progress @derkom almost there :)
@exxos - I remember we spent several days measuring the RESET switch when looking at the 3D models and footprints as they didn't match up.
@exxos - I remember we spent several days measuring the RESET switch when looking at the 3D models and footprints as they didn't match up.
-
exxos
- Site Admin
- Posts: 28361
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: derkom's attempt
@Icky Yeah, and after all that, it didn't line up anyway. I didn't have any switches to measure at the time, so went on the datasheet dimensions.. Should stop doing that...Icky wrote: 26 Nov 2019 21:08 @exxos - I remember we spent several days measuring the RESET switch when looking at the 3D models and footprints as they didn't match up.
-
PhilC
- Moderator
- Posts: 7443
- Joined: 23 Mar 2018 20:22
Re: derkom's attempt
It's not too bad a fit, just Bend the ground pins slightly and it fits. 8/10 for effort :lol:
If it ain't broke, test it to Destruction.
-
Icky
- Site Admin
- Posts: 4375
- Joined: 03 Sep 2017 10:57
- Location: UK
Re: derkom's attempt
Does that mean you have fitted yours then @PhilCPhilC wrote: 26 Nov 2019 21:58 It's not too bad a fit, just Bend the ground pins slightly and it fits. 8/10 for effort :lol:
Who is online
Users browsing this forum: ClaudeBot and 6 guests