16MHZ OPTIONAL FIX
Got the wire a little too hot here and melted back the insulation further than I'd like, but nothing risky is nearby, so it'll do.
(Yes, I did just cut that resistor off at the board instead of desolder it.)
REMINDER - Stay logged in for at least 2 hours a week to get whitelisted.
Also it helps build a picture where our "good traffic" is coming from for detection scripts.
:o)
Also it helps build a picture where our "good traffic" is coming from for detection scripts.
:o)
derkom - Progress
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
You do not have the required permissions to view the files attached to this post.
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
Quick question about the GLUE DATALINE FIX...
In step 1, it says, "Cut D0 & D1 tracks on the bottom of the PCB" and the red indicator covers two tracks in the picture:
Is it correct to cut both tracks covered by the red line, not just the yellow track? Since the instructions say to cut D0 and D1, and the non-yellow track goes to D0, I think I know the answer, but I want to double check with you guys before I cut. :?
In step 1, it says, "Cut D0 & D1 tracks on the bottom of the PCB" and the red indicator covers two tracks in the picture:
Is it correct to cut both tracks covered by the red line, not just the yellow track? Since the instructions say to cut D0 and D1, and the non-yellow track goes to D0, I think I know the answer, but I want to double check with you guys before I cut. :?
You do not have the required permissions to view the files attached to this post.
-
exxos
- Site Admin
- Posts: 28563
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: derkom - Progress
Yes, cut both tracks :)
If you zoom the image, you can see D0 & D1 on the IC holes.
If you zoom the image, you can see D0 & D1 on the IC holes.
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
Yep, I did see the labels. Just wanted to be ultra-sure before cutting. Thanks! :)exxos wrote: 14 Oct 2018 11:49 Yes, cut both tracks :)
If you zoom the image, you can see D0 & D1 on the IC holes.
-
exxos
- Site Admin
- Posts: 28563
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: derkom - Progress
Always a good plan! :)
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
So, life got in the way and kept me away from this project for a long time. I've finally picked it up again and made some progress, although I'm not getting video (more on this later).
For now, various pullups and the GLUE dataline patch (don't ask about the bits in the corner):
For now, various pullups and the GLUE dataline patch (don't ask about the bits in the corner):
You do not have the required permissions to view the files attached to this post.
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
MFP fix, keyboard resistor fix, ACIA dataline fix ...
You do not have the required permissions to view the files attached to this post.
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
RAM RW fix ...
You do not have the required permissions to view the files attached to this post.
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
1772 IRQ typo fix ...
You do not have the required permissions to view the files attached to this post.
-
derkom
- Moderator
- Posts: 1232
- Joined: 29 Jul 2018 18:45
Re: derkom - Progress
Floppy pullups fix ...
You do not have the required permissions to view the files attached to this post.
Who is online
Users browsing this forum: ClaudeBot and 2 guests