You will not be able to post if you are still using Microsoft email addresses such as Hotmail etc
See here for more information viewtopic.php?f=20&t=7296
BOOKMARK THIS PAGE !
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
DO NOT USE MOBILE / CGNAT DEVICES WHERE THE IP CHANGES CONSTANTLY!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!

kodak80 H5 A3 builds

Share your building progress here!
User avatar
kodak80
Posts: 524
Joined: 21 Oct 2017 01:14
Location: Brisbane, QLD, Australia

Re: kodak80 H5 A3 builds

Post by kodak80 »

exxos wrote: 22 Jan 2021 22:08
kodak80 wrote: 22 Jan 2021 22:00 I have a question regarding SMD resistor network (RN) components. Does the orientation of SMD RN on the H5 boards matter?
Nope, they are just single resistors in a "pack of 4".
Okay, good to know. Thank you.
Raven060 | Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Top
User avatar
kodak80
Posts: 524
Joined: 21 Oct 2017 01:14
Location: Brisbane, QLD, Australia

Re: kodak80 H5 A3 builds

Post by kodak80 »

kodak80 wrote: 22 Jan 2021 22:00 I have put aside the A3 board for now and started to build my three B1 boards up.
Okay, 3 years later and I have finally got back to looking at why this H5 A3 board was not booting. Turns out the fix on the reset IC22 was soldered to the GND pin 1 and not pin 2 :oops:

Image

The board is now booting and shows a desktop so another one comes to life. :)

Here is the correct location of the IC22 bodge wire:

reset H5 A3 fixed.jpg

I guess this means that my other three A3 boards should now be built up.
You do not have the required permissions to view the files attached to this post.
Raven060 | Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Top
User avatar
kodak80
Posts: 524
Joined: 21 Oct 2017 01:14
Location: Brisbane, QLD, Australia

Re: kodak80 H5 A3 builds

Post by kodak80 »

Having gotten the first H5 A3 board booting, I now have board 2 alive and booting.

On board 2, I added all the fixes bodge wires on the top leaving the bottom side clear of wires. :D

Board 3 and 4 will also be brought to life.
Raven060 | Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Top
User avatar
HigashiJun
Posts: 2247
Joined: 19 Jun 2020 07:21
Location: Tokyo

Re: kodak80 H5 A3 builds

Post by HigashiJun »

:D
Top
User avatar
exxos
Site Admin
Site Admin
Posts: 28074
Joined: 16 Aug 2017 23:19
Location: UK

Re: kodak80 H5 A3 builds

Post by exxos »

:bravo: :girldance:
Top

Return to “H5 A3 USER BUILDS”

Who is online

Users browsing this forum: CCBot and 1 guest