TF1230 Beta Interest (Open Source)

[KTron3]

Mark, is this correct? Both are the same Thin Quad Flat Pack 144 pin, as far as I am aware the G just indicates that it is certified lead free?

Happy to be shot down here!?

You are Indeed correct
6197744E-48A1-4672-B409-61B3BD44E755.png

Nice, G means pb free. Answers my question!! Thx a lot. @go0se @Avinitlarge !!

[terriblefire]

To be clear. You need to support the buyer if you manufacture and sell a TF1230. Legally you are the manufacturer and must give a 6 year warranty. If you do not you are in breach of the license and are breaking the law in the EU.

[drwhy]

... hmm ...

does the TF1230 IDE port work with 128mb RAM ?

before I had my card builded with 64mb of RAM and ehIDE is working,
now upgraded to 128mb and the CF-card on the ehIDE.device isn't recognised anymore.

I am using FW from tf1230r1_2021_10_01_beta and AOS3.2.1
AmigaTestKit 1.18 gives me no errors on RAM test.

[terriblefire]

... hmm ...

does the TF1230 IDE port work with 128mb RAM ?

before I had my card builded with 64mb of RAM and ehIDE is working,
now upgraded to 128mb and the CF-card on the ehIDE.device isn't recognised anymore.

I am using FW from tf1230r1_2021_10_01_beta and AOS3.2.1
AmigaTestKit 1.18 gives me no errors on RAM test.

I cannot think of any reason why the ram and the IDE would interfere with each other

[Ally]

... hmm ...

does the TF1230 IDE port work with 128mb RAM ?

Works beautifully in one of my A1200!

[KTron3]

To be clear. You need to support the buyer if you manufacture and sell a TF1230. Legally you are the manufacturer and must give a 6 year warranty. If you do not you are in breach of the license and are breaking the law in the EU.

Only for my 2 A1200

[ICRY]

Hello All,

I don't know if it's because I have fitted a 288 to a TF1230 but the CPLD gets hot approx. 40c running demos, games, but the card runs fine, so just wondering if this is a normal ish temp for the CPLD etc, or possibly something else, I can always add a heatsink tho.

[supaduper]

Hello All,

I don't know if it's because I have fitted a 288 to a TF1230 but the CPLD gets hot approx. 40c running demos, games, but the card runs fine, so just wondering if this is a normal ish temp for the CPLD etc, or possibly something else, I can always add a heatsink tho.

40c is excessive, they will get warm but should not be that hot I would put heatsink on it

[terriblefire]

... hmm ...

does the TF1230 IDE port work with 128mb RAM ?

before I had my card builded with 64mb of RAM and ehIDE is working,
now upgraded to 128mb and the CF-card on the ehIDE.device isn't recognised anymore.

I am using FW from tf1230r1_2021_10_01_beta and AOS3.2.1
AmigaTestKit 1.18 gives me no errors on RAM test.

If this is still a problem can you tell me how much fastram is reported? Can you softload other modules?

[SlCKB0Y]

Anyways here we are... all the TF1230 schematics, gerbers, cpl and bom files... DO NOT ASK me how you use these... if you dont know walk away..

tf1230r1_archive.zip

Hello everyone! Sorry if this is an obvious question as i'm completely new here.

I am intending on ordering some TF1230 boards (JLPCB) and I just wanted to make sure that the Gerbers/BoM attached to the second post of this thread (in a zip) were the most up-to-date revision?

Thanks!