Stuff and Things.

[terriblefire]

@terriblefire

I watched your presentation on the RMC channel over on YouTube last night (Legends in the Cave.) and it was really interesting and informative.

Thanks for you continued contributions to everything retro

Thanks. Glad people enjoyed it. I worried it was very very dull

[rubber_jonnie]

@terriblefire

I watched your presentation on the RMC channel over on YouTube last night (Legends in the Cave.) and it was really interesting and informative.

Thanks for you continued contributions to everything retro

Thanks. Glad people enjoyed it. I worried it was very very dull

It was far from dull

[rubber_jonnie]

Well, it's been a while since I considered picking up one of these, the 2nd computer I ever owned, a rubbery Spectrum:

PXL_20230831_075421583.jpg (273.99 KiB) Viewed 913 times

I may do a separate write up, depending on the need for repairs.

Also in the picture are an HDMI tester, needed for the PS4 diagnostics, and an HDMI breakout board to help me test connections at the port itself.

[stephen_usher]

[chronicthehedgehog]

WIN_20230831_12_50_21_Pro.jpg (84.95 KiB) Viewed 898 times

Just felt the need to share my *hilarious* breadboard.

The right side is just an AY chip/beeper through monitor
The left side is my lame attempt to interface the Spectrum with a CMOD-S7

[rubber_jonnie]

WIN_20230831_12_50_21_Pro.jpg

Just felt the need to share my *hilarious* breadboard.

The right side is just an AY chip/beeper through monitor
The left side is my lame attempt to interface the Spectrum with a CMOD-S7

I've never seen so many wires hanging off a Speccy

The biggest breadboard project I did was a latch card to sound chip on my ZX81. It was limited, but actually worked ok. All lost to the mists of time sadly...

[rubber_jonnie]

Another arrival, a cool little book that holds a lot of nostalgia for me, taking me back to the days of Tandy/Radio Shack:

PXL_20230831_115256169.jpg (182.84 KiB) Viewed 896 times

It's full of neat little circuits.

[HigashiJun]

Well, it's been a while since I considered picking up one of these, the 2nd computer I ever owned, a rubbery Spectrum:


PXL_20230831_075421583.jpg


I may do a separate write up, depending on the need for repairs.

Also in the picture are an HDMI tester, needed for the PS4 diagnostics, and an HDMI breakout board to help me test connections at the port itself.

Nice, but you will soon have no more room for all that stuff !

[rubber_jonnie]

Well, it's been a while since I considered picking up one of these, the 2nd computer I ever owned, a rubbery Spectrum:


PXL_20230831_075421583.jpg


I may do a separate write up, depending on the need for repairs.

Also in the picture are an HDMI tester, needed for the PS4 diagnostics, and an HDMI breakout board to help me test connections at the port itself.

Nice, but you will soon have no more room for all that stuff !

That's what my wife says, but I always find a little more space

[chronicthehedgehog]

I've never seen so many wires hanging off a Speccy

The biggest breadboard project I did was a latch card to sound chip on my ZX81. It was limited, but actually worked ok. All lost to the mists of time sadly...

and it almost worked.

I'd attached a raspi to the S7. Hand-coded a UART, circular FIFOs, CDC stuff etc in system verilog (because I didn't really understand AXI mainly). My first project was to allow various USB HIDs to be attached to the Spectrum via the PI but I couldn't figure out why I was getting two reads on my FIFO for every IORQ from the Spectrum.

I guess it was down to timing/constraints on the FPGA but that was way above my level of expertise and I never could find any info on it (beyond the 'hello world' type stuff). Shelved indefinitely but I can't bring myself to tear apart the breadboard - just in case I get the urge to do some Verilog

It really attracts the dust