Sun Ultrasparc
- stephen_usher
- Site sponsor

- Posts: 7724
- Joined: Mon Nov 13, 2017 7:19 pm
- Location: Oxford, UK.
- Contact:
Re: Sun Ultrasparc
Hot air is your friend when trying to get that epoxy potting off. It crumbles if heated to ~200C.
Intro retro computers since before they were retro...
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
Re: Sun Ultrasparc
Ok yes I saw that indeed but I don't have a hot air station but I assume the correct metal pins are now exposed for receiving a wire. So a knife also works.
- stephen_usher
- Site sponsor

- Posts: 7724
- Joined: Mon Nov 13, 2017 7:19 pm
- Location: Oxford, UK.
- Contact:
Re: Sun Ultrasparc
I'm just experimenting with roasting the chip in the oven as an alternative.
Intro retro computers since before they were retro...
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
Re: Sun Ultrasparc
Short update. Bought some fans to replace the old ones. The bearing in the original fans are gone. They are based on a piece of foam which is powder now..
Case fan + cpu:
Case fan + cpu:
Re: Sun Ultrasparc
So my local electronic part shop stopped so I need to order everything now
Finally Recieved the battery holder. But indeed this fixed the nvram issue.
Next step reinstall videocard and test video out..
Finally Recieved the battery holder. But indeed this fixed the nvram issue.
Next step reinstall videocard and test video out..
Re: Sun Ultrasparc
So found this Eizo monitor in my storage. I thought it was multisync and usable on my Atari ST but no.. However it seems to work great with the Sun as this monitor has sync on green.
And we have output…
Next get some scsi things going.
And what to do with case… Painting… But i need stickers then and for the keyboard as well and I have two missing keycaps..
And I need a mouse but maybe a picopi can be used.. with a standard usb.
And which OS. I’m thinking Solaris 2.8 and netbsd now… in dual boot.
Update: the harddisk seems fully empty…..
And we have output…
Next get some scsi things going.
And what to do with case… Painting… But i need stickers then and for the keyboard as well and I have two missing keycaps..
And I need a mouse but maybe a picopi can be used.. with a standard usb.
And which OS. I’m thinking Solaris 2.8 and netbsd now… in dual boot.
Update: the harddisk seems fully empty…..
Re: Sun Ultrasparc
Consider OpenBSD too, I had a very nice and easy time installing it on my Sun.
- stephen_usher
- Site sponsor

- Posts: 7724
- Joined: Mon Nov 13, 2017 7:19 pm
- Location: Oxford, UK.
- Contact:
Re: Sun Ultrasparc
With an Ultra 1 I wouldn't take it beyond Solaris 2.6 actually. It's unlikely to be supported in 64 bit mode as only the very last versions with updated UltraSPARC CPUs would run in 64 bit mode reliably. Solaris userland is all 32 bit anyway, unless you compile specifically for sparcv9, and that's true right up to Solaris 10.
Intro retro computers since before they were retro...
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
Re: Sun Ultrasparc
So tried booting some stuff…. But this a real nightmare.
Tried AI help. It tells me that the openboot version is a complete mismatch for this computer as it is a 170e and not a 170..
Hardware & Configuration:
• System: Sun Ultra 1 Model 170E motherboard (show-devs confirms SUNW,fas Fast/Wide SCSI and SUNW,hme Ethernet), 192 MB RAM (64 MB Bank 0 + 128 MB Bank 1), headless over serial (ttya, 9600 8N1).
• Firmware: Running OpenBoot 3.0, reporting Sun Ultra 1 UPA/SBus (UltraSPARC 167MHz) in the banner.
• Storage: 80-pin SCA ZuluSCSI plugged directly into the internal SCA backplane.
The Issue:
Any boot attempt from the 80-pin ZuluSCSI loads the initial bootloader (ufsboot for Solaris or Bootblk 2.1 for OpenBSD) and then immediately crashes/resets silently with zero additional output (even with boot -kv).
What I have already tried (all give the exact same crash after ufsboot / Bootblk 2.1):
1. Solaris Releases: Tested both base Solaris 2.5.1 and Solaris 2.5.1 Hardware: 11/97 (2.5.1.1197, SPARC).
2. Other OS & Disk Images:
• Tested OpenBSD/sparc64 (cd80.iso) — crashes silently right after Bootblk 2.1.
• Tested a pre-installed HD0.img hard disk image (boot disk) — crashes silently right after ufsboot.
3. ZuluSCSI Configuration (zuluscsi.ini):
• Set BlockSize = 512, Quirks = 2, and Sun/Toshiba CD-ROM inquiry strings (XM-5701TASUN12XCD), verified in zululog.txt.
• Tested both SCSI ID 6 (boot cdrom) and SCSI ID 0 (boot disk / boot disk:f).
4. OpenBoot Variables:
• Set diag-switch? false, auto-boot? false, tpe-link-test? false, and input-device/output-device to ttya.
AI Diagnosis / Conclusion:
Based on troubleshooting this with an AI assistant, the conclusion is that OpenBoot 3.0 is the wrong firmware for a 170E motherboard (which should be on OpenBoot 3.1+ / 3.25) and breaks SUNW,fas Wide-SCSI initialization/handoff (alongside potential missing high-byte termination from the 80-pin narrow ZuluSCSI on the 16-bit Wide SCA backplane).
Question:
Can anyone confirm if this AI conclusion is accurate, and is boot net (via hme0) to flash the PROM to OpenBoot 3.25 (Patch 105669-07) the right way to fix it, or is there an easier workaround?
Tried AI help. It tells me that the openboot version is a complete mismatch for this computer as it is a 170e and not a 170..
Hardware & Configuration:
• System: Sun Ultra 1 Model 170E motherboard (show-devs confirms SUNW,fas Fast/Wide SCSI and SUNW,hme Ethernet), 192 MB RAM (64 MB Bank 0 + 128 MB Bank 1), headless over serial (ttya, 9600 8N1).
• Firmware: Running OpenBoot 3.0, reporting Sun Ultra 1 UPA/SBus (UltraSPARC 167MHz) in the banner.
• Storage: 80-pin SCA ZuluSCSI plugged directly into the internal SCA backplane.
The Issue:
Any boot attempt from the 80-pin ZuluSCSI loads the initial bootloader (ufsboot for Solaris or Bootblk 2.1 for OpenBSD) and then immediately crashes/resets silently with zero additional output (even with boot -kv).
What I have already tried (all give the exact same crash after ufsboot / Bootblk 2.1):
1. Solaris Releases: Tested both base Solaris 2.5.1 and Solaris 2.5.1 Hardware: 11/97 (2.5.1.1197, SPARC).
2. Other OS & Disk Images:
• Tested OpenBSD/sparc64 (cd80.iso) — crashes silently right after Bootblk 2.1.
• Tested a pre-installed HD0.img hard disk image (boot disk) — crashes silently right after ufsboot.
3. ZuluSCSI Configuration (zuluscsi.ini):
• Set BlockSize = 512, Quirks = 2, and Sun/Toshiba CD-ROM inquiry strings (XM-5701TASUN12XCD), verified in zululog.txt.
• Tested both SCSI ID 6 (boot cdrom) and SCSI ID 0 (boot disk / boot disk:f).
4. OpenBoot Variables:
• Set diag-switch? false, auto-boot? false, tpe-link-test? false, and input-device/output-device to ttya.
AI Diagnosis / Conclusion:
Based on troubleshooting this with an AI assistant, the conclusion is that OpenBoot 3.0 is the wrong firmware for a 170E motherboard (which should be on OpenBoot 3.1+ / 3.25) and breaks SUNW,fas Wide-SCSI initialization/handoff (alongside potential missing high-byte termination from the 80-pin narrow ZuluSCSI on the 16-bit Wide SCA backplane).
Question:
Can anyone confirm if this AI conclusion is accurate, and is boot net (via hme0) to flash the PROM to OpenBoot 3.25 (Patch 105669-07) the right way to fix it, or is there an easier workaround?
- stephen_usher
- Site sponsor

- Posts: 7724
- Joined: Mon Nov 13, 2017 7:19 pm
- Location: Oxford, UK.
- Contact:
Re: Sun Ultrasparc
I take it that you've set the memory test size environment variable to the size of your memory and then run 'test-memory'?
Sounds a lot like your machine's memory has issues... or the CPU is duff.
I take it that you've looked at the Service Manual?
You can find the BootPROM versions here: https://archives.retrobridge.org/sun/sy ... ml#U1_170E
Sounds a lot like your machine's memory has issues... or the CPU is duff.
I take it that you've looked at the Service Manual?
You can find the BootPROM versions here: https://archives.retrobridge.org/sun/sy ... ml#U1_170E
Intro retro computers since before they were retro...
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
ZX81->Spectrum->Memotech MTX->Sinclair QL->520STM->BBC Micro->TT030->PCs & Sun Workstations.
Added code to the MiNT kernel (still there the last time I checked) + put together MiNTOS.
Collection now with added Macs, Amigas, Suns and Acorns.
