Page 5 of 26
Re: Phil C's Raven build
Posted: 13 May 2025 16:24
by PhilC
Just for a bit of fun, here's the gembench results with the standard emutos VGA driver.
The CPU is running at 80mhz. Its a 66 MHz rev 4 LC. I've got a rev 5 full 060 to replace it with once it's all up and running properly.
PXL_20250513_152143766~2.jpg
Re: Phil C's Raven build
Posted: 13 May 2025 16:51
by exxos
:yay: :yay:
That's like NVDI speeds, but without NVDI :lol:
Re: Phil C's Raven build
Posted: 13 May 2025 16:55
by Steve
Amazing work Phil, great job :D
Re: Phil C's Raven build
Posted: 13 May 2025 17:27
by PhilC
Thanks @Steve. I'll probably bring it to CL4 once I've got it looking like I want it.
@exxos you should see the results with the nova drivers installed. I'll have to try find a copy of NVDI, then we should get ridiculous speeds :lol:
Might build myself another one,maybe in Purple this time?
Thank you @agranlund for your hard work and assistance in getting it all up and running.
Re: Phil C's Raven build
Posted: 13 May 2025 18:04
by JezC
Still hoping for a lottery win to be able to afford one of these some day :roll:
Not helped by ordering the ATW800/2 a week ago though... maybe that plus my TRAM module (if it still works) and the Transputer ISA card in an old PC would be good for CL4...
Re: Phil C's Raven build
Posted: 13 May 2025 18:33
by PhilC
JezC wrote: 13 May 2025 18:04
Still hoping for a lottery win to be able to afford one of these some day :roll:
Not helped by ordering the ATW800/2 a week ago though... maybe that plus my TRAM module (if it still works) and the Transputer ISA card in an old PC would be good for CL4...
Sounds like an interesting lot to bring Jez
Re: Phil C's Raven build
Posted: 13 May 2025 18:47
by mrbombermillzy
Well done
@PhilC Finally got there! :cheer:
JezC wrote: 13 May 2025 18:04
maybe that plus my TRAM module (if it still works) and the Transputer ISA card in an old PC would be good for CL4...
Somehow, I had a feeling someone was going to bring a Transputer to CL4. :lol:
Although beware; I may be picking your brains for technical info. :D
Re: Phil C's Raven build
Posted: 13 May 2025 18:58
by agranlund
Nice , super cool to see another one running :)
Great job @PhilC !
Re: Phil C's Raven build
Posted: 13 May 2025 19:02
by JezC
mrbombermillzy wrote: 13 May 2025 18:47
Well done @PhilC Finally got there! :cheer:
JezC wrote: 13 May 2025 18:04
maybe that plus my TRAM module (if it still works) and the Transputer ISA card in an old PC would be good for CL4...
Somehow, I had a feeling someone was going to bring a Transputer to CL4. :lol:
Although beware; I may be picking your brains for technical info. :D
Yes, well done
@PhilC
@mrbombermillzy it might even be 3 real Transputers plus the emulated one on the ATW800/2...
Re: Phil C's Raven build
Posted: 13 May 2025 19:23
by dml
Great! Well done getting it to run!