Page 9 of 21
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 19:01
by rubber_jonnie
If all is well, the IDE interface will be getting a try out.
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 20:16
by exxos
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 21:11
by PaulJ
@rubber_jonnie , I told
@PhilC earlier that you were in training and was going to kick some serious butt building the H4! Don't let him try and pawn off his fupaw on you so he can expunge the fame that has come with his perpendicular IC installation technique.
pa.png
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 21:14
by rubber_jonnie
Funnily enough I'm just on the way home from karate training 😁
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 21:16
by PhilC
PaulJ wrote: 14 Feb 2020 21:11
@rubber_jonnie , I told @PhilC earlier that you were in training and was going to kick some serious butt building the H4! Don't let him try and pawn off his fupaw on you so he can expunge the fame that has come with his perpendicular IC installation technique.
pa.png
But it genuinely fit better that way round.
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 21:40
by PaulJ
PhilC wrote: 14 Feb 2020 21:16
PaulJ wrote: 14 Feb 2020 21:11
@rubber_jonnie , I told @PhilC earlier that you were in training and was going to kick some serious butt building the H4! Don't let him try and pawn off his fupaw on you so he can expunge the fame that has come with his perpendicular IC installation technique.
pa.png
But it genuinely fit better that way round.
I have to give ya that... when I first looked at it that looked right but after a little research... nope. So I had to purchase my own award!!
IMG_2452.JPG
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 21:44
by PaulJ
rubber_jonnie wrote: 14 Feb 2020 21:14
Funnily enough I'm just on the way home from karate training 😁
All excited to kick some Butt I assume.. :excited:
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 14 Feb 2020 22:09
by rubber_jonnie
PaulJ wrote: 14 Feb 2020 21:44
rubber_jonnie wrote: 14 Feb 2020 21:14
Funnily enough I'm just on the way home from karate training 😁
All excited to kick some Butt I assume.. :excited:
Definitely!
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 15 Feb 2020 09:53
by rubber_jonnie
PaulJ wrote: 14 Feb 2020 21:11
@rubber_jonnie , I told @PhilC earlier that you were in training and was going to kick some serious butt building the H4! Don't let him try and pawn off his fupaw on you so he can expunge the fame that has come with his perpendicular IC installation technique.
pa.png
Hmm, yes, intersting orientation!
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 15 Feb 2020 14:08
by rubber_jonnie
Well, I really wish I'd fitted the LS11 when I was doing all the other SMT stuff, because with everything around it it wa completely hideous to fit to the point where I may have shouted at it once or twice.
The pins buzz out to where they should though and there's no shorts.
Bad news is that I still just get a white screen during boot, and when scoping out things like /HALT, /AS etc, I see the same as on my Mega 4, which also boots to a white screen.
/HALT is permanently low, apart from reset when it jumps high brifly, so either the CPU is getting garbage data and halting, or something else is causing the line to stay low, some sort of HW issue.
Onwards and upwards as they say, diag cart time, plus some of the suggestions @exxos made re the Mega4. I wan't to get both of them running, and it's soaking up a lot of my time, but hey ho, isn't that the pointof a hobby?