exxos's Atari, Amiga & retro forum

terriblefire wrote: 18 Dec 2020 21:26

arkadiusz.makarenko wrote: 18 Dec 2020 20:16 I have ordered some missing parts good few days ago... but I am loosing hope of getting it this year.

what you missing?

Main bit connectors. Mouser started moving my order, so there is still a chance.
I should have ordered it long time ago...

arkadiusz.makarenko wrote: 18 Dec 2020 22:33

terriblefire wrote: 18 Dec 2020 21:26
what you missing?

Main bit connectors. Mouser started moving my order, so there is still a chance.
I should have ordered it long time ago...

i'll send you two with my board.

I have ordered PCBs, so I am planning to make some prototypes.

arkadiusz.makarenko wrote: 25 Dec 2020 23:14 I have ordered PCBs, so I am planning to make some prototypes.

Apologies. Wife fell over and broke her ankle before xmas so have had zero time.

terriblefire wrote: 29 Dec 2020 13:55

arkadiusz.makarenko wrote: 25 Dec 2020 23:14 I have ordered PCBs, so I am planning to make some prototypes.

Apologies. Wife fell over and broke her ankle before xmas so have had zero time.

Shit. I hope it was not serious fracture?

I can't reply to your PM. But I will do it what you asked me.

PS.
I need to do few boards and test them on my CD32, and check if it behaves the same on different machines. So I though that I would build few test risers, and give some away to people who can do some troubleshooting for me in case of issues.

arkadiusz.makarenko wrote: 29 Dec 2020 21:34 Shit. I hope it was not serious fracture?

I can't reply to your PM. But I will do it what you asked me.

PS.
I need to do few boards and test them on my CD32, and check if it behaves the same on different machines. So I though that I would build few test risers, and give some away to people who can do some troubleshooting for me in case of issues.

Its not bad but in a cast thing.

Do you have a binary for the rev 1 riser i can flash? i was going to look at the CD32 again maybe in the new year .

terriblefire wrote: 29 Dec 2020 21:43

arkadiusz.makarenko wrote: 29 Dec 2020 21:34 Shit. I hope it was not serious fracture?

I can't reply to your PM. But I will do it what you asked me.

PS.
I need to do few boards and test them on my CD32, and check if it behaves the same on different machines. So I though that I would build few test risers, and give some away to people who can do some troubleshooting for me in case of issues.

Its not bad but in a cast thing.

Do you have a binary for the rev 1 riser i can flash? i was going to look at the CD32 again maybe in the new year .

I have pushed todays set of binaries here. https://github.com/arkadiuszmakarenko/T ... r_binaries

I have introduced 1 us delay at the end of irq handling in this one, as occasionally Amiga didn't boot without delay. It is 1us as I have it done for other things, and going sub 1us is a little bit tricky (will look at this if this firmware will boot and work on various cd32s)

arkadiusz.makarenko wrote: 29 Dec 2020 22:44 I have pushed todays set of binaries here. https://github.com/arkadiuszmakarenko/T ... r_binaries

Will that work on the previous version of the board?

terriblefire wrote: 29 Dec 2020 22:52

arkadiusz.makarenko wrote: 29 Dec 2020 22:44 I have pushed todays set of binaries here. https://github.com/arkadiuszmakarenko/T ... r_binaries

Will that work on the previous version of the board?

I don't think so. Keyboard and control signals changed pins.

arkadiusz.makarenko wrote: 29 Dec 2020 23:05

terriblefire wrote: 29 Dec 2020 22:52

Will that work on the previous version of the board?

I don't think so. Keyboard and control signals changed pins.

Ok.. I only have rev 1 built right now. Rev 2 still staring at me...

Rev 0 in bin. Will this firmware work on rev 1.. (because filename says rev1).