Page 5 of 6

Re: Damage done to my STE

Posted: 19 Sep 2019 20:55
by Bikerbob
jumpers2.jpg
jumpers2.jpg (122.5 KiB) Viewed 4341 times

Re: Damage done to my STE

Posted: 19 Sep 2019 21:15
by exxos
Bikerbob wrote: 19 Sep 2019 20:47 Sorry Chris, I dont understand just 2 pictures? So your saying there is only the one trace that goes to the Via to the other side.. thats it?
I highlighted the trace you was questioning... I think your not seeing exactly where the traces go and its resulting in the confusion.

Re: Damage done to my STE

Posted: 19 Sep 2019 21:52
by Bikerbob
So then as I said.. just the one trace that goes to the via to the other side of the board to the ROM?

James

Re: Damage done to my STE

Posted: 19 Sep 2019 21:55
by exxos
Bikerbob wrote: 19 Sep 2019 21:52 So then as I said.. just the one trace that goes to the via to the other side of the board to the ROM?
I don't know which vias your referring to.. I highlighted the ones you mention anyway.. its better just to look at the images to see where things go.

Re: Damage done to my STE

Posted: 19 Sep 2019 22:09
by Bikerbob
This is why sometimes this is better in PMs.. there seems to be a communication issue.. So layer 4 is the bottom? where I pulled the pad from?

SO I will need to jumper to make the trace you highlighted work.. correct?

James

Re: Damage done to my STE

Posted: 19 Sep 2019 22:11
by exxos
I think this one is your only issue you had....

https://www.exxosforum.co.uk/forum/viewt ... =30#p26304

Re: Damage done to my STE

Posted: 20 Sep 2019 06:36
by Bikerbob
Fixed! - fired up and working.

Have an HXC Gotek with it.. need to figureout how to setup the USB drive... off to the website!

James

ROWBU7x.jpg
ROWBU7x.jpg (357.16 KiB) Viewed 4320 times
!Message from: Moderator
@Bikerbob, we have placed your attachments in-line so they display correctly in your post. Here's the how-to guide.

Re: Damage done to my STE

Posted: 20 Sep 2019 07:27
by derkom
Bikerbob wrote: 19 Sep 2019 18:21 Are you saying that if the TOS switcher is in.. and there is no floppy connected to the cable that there would be boot issues?? but not at the point I am at correct??

you would get a screen etc??

Because I dont have a floppy connected in testing this.
It's a TOS 2.06 misbehaviour issue that I knew eons ago, but had forgotten before installing the TOS switcher in the STe I picked up. Without a floppy connected, it'll do the RAM test, but then four bombs instead of move on to the desktop. Unrelated to the TOS switcher.

Re: Damage done to my STE

Posted: 20 Sep 2019 09:02
by rubber_jonnie
Bikerbob wrote: 20 Sep 2019 06:36 Fixed! - fired up and working.

Have an HXC Gotek with it.. need to figureout how to setup the USB drive... off to the website!

James
Try here as well for Gotek :)

https://www.exxosforum.co.uk/forum/viewt ... ilit=gotek

Re: Damage done to my STE

Posted: 20 Sep 2019 15:48
by Bikerbob
rubber_jonnie wrote: 20 Sep 2019 09:02
Bikerbob wrote: 20 Sep 2019 06:36 Fixed! - fired up and working.

Have an HXC Gotek with it.. need to figureout how to setup the USB drive... off to the website!

James
Try here as well for Gotek :)

https://www.exxosforum.co.uk/forum/viewt ... ilit=gotek
Thanks - yep I know FF.. this one has HXC on it.. so thought I would try it. Never played with it. I have played with FF for years though.. Keir has done some terrific stuff.

James