Page 37 of 337
Re: exxos blog - random goings on
Posted: 15 Jul 2019 18:13
by exxos
Box of 4MB STFM boards arrived :) I think I got 50 made... time to start testing them :)
IMG_4454.JPG
Re: exxos blog - random goings on
Posted: 19 Jul 2019 18:23
by exxos
Finally had five seconds to look at this again... Basically there is not enough "IO power" in a GAL22V10 :( I'm actually one output pin short in order to put the AB SWAP in that GAL as well :(
so either the ABSWAP just remains as jumpers, or I move to the ATF1502... Which seems a bit of a overkill for this part of the circuit :roll:
In order to keep things simple, I will likely just stick with a normal 22V10 and port over my V7 floppy mod directly.
meh.jpg
Re: exxos blog - random goings on
Posted: 19 Jul 2019 19:13
by exxos
Added in the PLCC version of the MFP. I have a stack of them anyway and theres room for it :)
52.jpg
Re: exxos blog - random goings on
Posted: 19 Jul 2019 19:19
by PhilC
Mongrel is going to be an understatement at this rate :D
Re: exxos blog - random goings on
Posted: 19 Jul 2019 19:26
by exxos
PhilC wrote: 19 Jul 2019 19:19
Mongrel is going to be an understatement at this rate :D
Yeah, its a mash up of anything which will fit at the moment :lol:
Wonder if I should integrate the diagnostic cart as well :lol: :roll: Must...Stop... Having.. Ideas...... So MSHI is now a new shortie :lol:
Re: exxos blog - random goings on
Posted: 19 Jul 2019 19:34
by PhilC
Lol, could come up with a few more if you wanted (ide) :lol:
Re: exxos blog - random goings on
Posted: 19 Jul 2019 19:55
by exxos
PhilC wrote: 19 Jul 2019 19:34
Lol, could come up with a few more if you wanted (ide) :lol:
IDE not finished yet :) Pretty sure Icky broke the boards... Though if by some mega huge sugar-feed turbo effort by everyone, in that we got the IDE2 working quickly, we could consider integrating it.. but I think nothing else will be ready in time for the H2 production run.
BTW Phil, do you have a Atmel programmer to program the ATF15xx series ? (can't remember)
Re: exxos blog - random goings on
Posted: 19 Jul 2019 20:09
by Icky
exxos wrote: 19 Jul 2019 19:55
PhilC wrote: 19 Jul 2019 19:34
Lol, could come up with a few more if you wanted (ide) :lol:
IDE not finished yet :) Pretty sure Icky broke the boards... Though if by some mega huge sugar-feed turbo effort by everyone, in that we got the IDE2 working quickly, we could consider integrating it.. but I think nothing else will be ready in time for the H2 production run.
BTW Phil, do you have a Atmel programmer to program the ATF15xx series ? (can't remember)
Not broken yet :) Just need to get the two we have working.
Re: exxos blog - random goings on
Posted: 19 Jul 2019 20:23
by PhilC
Icky wrote: 19 Jul 2019 20:09
exxos wrote: 19 Jul 2019 19:55
IDE not finished yet :) Pretty sure Icky broke the boards... Though if by some mega huge sugar-feed turbo effort by everyone, in that we got the IDE2 working quickly, we could consider integrating it.. but I think nothing else will be ready in time for the H2 production run.
BTW Phil, do you have a Atmel programmer to program the ATF15xx series ? (can't remember)
Not broken yet :) Just need to get the two we have working.
Now Now, the breaking bit is my job and yes I did get an ATF programmer..... its in the pile on the floor, somewhere.
Re: exxos blog - random goings on
Posted: 19 Jul 2019 20:26
by Icky
PhilC wrote: 19 Jul 2019 20:23
Icky wrote: 19 Jul 2019 20:09
Not broken yet :) Just need to get the two we have working.
Now Now, the breaking bit is my job and yes I did get an ATF programmer..... its in the pile on the floor, somewhere.
Thats good to know as Exxos and I have been doing some more work on the Flashy Clock board today and have some updates but they will require programming the ATF1508 on the board. I will post on the Flashy Clock thread later.