Page 4 of 7

Re: Steve's DFB1 build

Posted: 20 Apr 2022 11:34
by Steve
Ohhh thank you FedEx!

PXL_20220420_103328990.jpg
PXL_20220420_103328990.jpg (497.13 KiB) Viewed 2537 times

Re: Steve's DFB1 build

Posted: 20 Apr 2022 11:42
by Steve
Okay but now I've broken my CPU.

PXL_20220420_104157230.jpg
PXL_20220420_104157230.jpg (386.64 KiB) Viewed 2535 times

Re: Steve's DFB1 build

Posted: 20 Apr 2022 11:58
by sporniket
EdvardMunch-TheScream-1893.jpg
EdvardMunch-TheScream-1893.jpg (80.43 KiB) Viewed 2531 times

Re: Steve's DFB1 build

Posted: 20 Apr 2022 12:24
by frank.lukas
.. you can solder new pins. That's enough to set up the CPU once.

Re: Steve's DFB1 build

Posted: 20 Apr 2022 12:29
by Steve
It's okay I got a spare :)

By the way before I test, @Badwolf I'm getting 21 ohms across vcc and gnd, would that be correct? CPU inserted etc.

PXL_20220420_112526397.MP.jpg
PXL_20220420_112526397.MP.jpg (442.52 KiB) Viewed 2525 times

Re: Steve's DFB1 build

Posted: 20 Apr 2022 12:30
by Steve
And just want to double check that I've got the Xtal installed correctly :)

PXL_20220420_112955077.jpg
PXL_20220420_112955077.jpg (294.27 KiB) Viewed 2523 times

Re: Steve's DFB1 build

Posted: 20 Apr 2022 12:33
by Badwolf
Steve wrote: 20 Apr 2022 12:29 By the way before I test, @Badwolf I'm getting 21 ohms across vcc and gnd, would that be correct? CPU inserted etc.
Whilst plugged into the Falcon? Seems reasonable. I could have even been persuaded it would be lower.

BW

Re: Steve's DFB1 build

Posted: 20 Apr 2022 12:34
by Badwolf
Steve wrote: 20 Apr 2022 12:30 And just want to double check that I've got the Xtal installed correctly :)
Yep. Pin one top right. Tiny silkscreen says "Oscillator this way -->" ;)

BTW, if you can, I prefer to test in RGB or Composite mode (versus VGA) as most tellys will react faster to the signal coming on than VGA screens (which tend to need to wake up).

Could potentially save 5 or 6 seconds of power if something's not right.

Remember you need to jumper the flash disable and, if I were you, I'd jumper the master disable on first power up: make sure you see the Atari logo from the on-board processor before trying the external one.

BW

Re: Steve's DFB1 build

Posted: 20 Apr 2022 12:41
by Steve
@Badwolf

I'm getting this:
(Diag cart in)

PXL_20220420_114038103.jpg
PXL_20220420_114038103.jpg (631.03 KiB) Viewed 2513 times

Re: Steve's DFB1 build

Posted: 20 Apr 2022 13:00
by Badwolf
Firstly, is this with the master enable jumpered or open?

If jumpered, reseat both board and diag cart.

If open, does jumpered work?

BW