Page 14 of 339
Re: exxos blog - random goings on
Posted: 10 May 2019 20:03
by exxos
It basically seems okay at first glance...
- IMG_4160.JPG (254.04 KiB) Viewed 4550 times
- IMG_4161.JPG (181.92 KiB) Viewed 4550 times
Looking at the rear I seem to have got the supports way too high :roll: I must have not taken off the thickness of the base when I measured these out :roll:
Just need a blank motherboard to check the hole alignments correctly now....
- IMG_4162.JPG (210.51 KiB) Viewed 4550 times
Re: exxos blog - random goings on
Posted: 10 May 2019 20:33
by exxos
..and a nice back view...
- 1.jpg (91.43 KiB) Viewed 4543 times
Re: exxos blog - random goings on
Posted: 10 May 2019 22:35
by exxos
Typical...
- 666.jpg (23.82 KiB) Viewed 4535 times
EDIT:
Less middle area now. I may put more struts in there, but don't think it really needs it... it will be a order of magnitude quicker to print thats for sure!
Holes on the back should be better now as well... Will have to wait until Monday before I can print it out again :(
- 55.jpg (67.24 KiB) Viewed 4534 times
Re: exxos blog - random goings on
Posted: 13 May 2019 10:25
by exxos
So it begins...
- Capture.JPG (87.1 KiB) Viewed 4509 times
Re: exxos blog - random goings on
Posted: 13 May 2019 15:19
by exxos
Looking a lot better this time...
- IMG_4165.JPG (87.78 KiB) Viewed 4498 times
Re: exxos blog - random goings on
Posted: 13 May 2019 17:48
by Icky
Nice - How sturdy is it?
So all you have left to do are some risers to fit between the PSU and motherboard?
Re: exxos blog - random goings on
Posted: 13 May 2019 19:15
by exxos
Icky wrote: 13 May 2019 17:48
Nice - How sturdy is it?
There is a tiny bit of bend on it all, but really not surprised. I have increased the angle part at the back slightly.. I will probably try a better infill on the next print, as it is only 15%... If there was printed solid I still think it would bend slightly.. Is nowhere near enough to break, but it is after all plastic and not metal.. I have been trying to break it and it's not possible.
Removing the hexagon pattern in the centre did not make it any less bendy.
Icky wrote: 13 May 2019 17:48
So all you have left to do are some risers to fit between the PSU and motherboard?
Yeah, they will be like the floppy plastic posts, that type of thing.
Re: exxos blog - random goings on
Posted: 13 May 2019 20:27
by PhilC
You should give it to somebody who is skilled in breaking :D
Looks good to me tho
Re: exxos blog - random goings on
Posted: 14 May 2019 13:43
by exxos
Just making myself a brew, the mug has swallowed my spoon :shock:
Might also need 2 teabags as well..
- IMG_20190511_123323.jpg (268.42 KiB) Viewed 4456 times
Re: exxos blog - random goings on
Posted: 14 May 2019 20:16
by Icky
exxos wrote: 14 May 2019 13:43
Just making myself a brew, the mug has swallowed my spoon :shock:
Might also need 2 teabags as well..
T is not strong enough until the spoon stands up on its own :)