Page 123 of 337
Re: exxos blog - random goings on
Posted: 22 Mar 2021 16:37
by exxos
Removed the nut lugs.. Also made the thickness of the whole thing 5 mm less... There is no use really overhanging the syringe barrel, it only needs to support sides and the back really. I had it before because the base of the syringe be under a lot of pressure so I did not want to risk breaking.. But thinking about it, the bulk of the pressure should be on the top side of syringe anyway.. The bottom of the syringe should be more just or alignment as opposed to strength.
- Capture.PNG (90.08 KiB) Viewed 5250 times
I am a bit stuck now, as I cannot do the mounting holes until my CNC framework arrives along with the motors etc :(
Re: exxos blog - random goings on
Posted: 22 Mar 2021 18:01
by exxos
Not collapsed yet :lol: :thumbup:
- IMG_6307.JPG (210.89 KiB) Viewed 5233 times
Re: exxos blog - random goings on
Posted: 22 Mar 2021 19:06
by exxos
Printed :) not sure why its got that odd couple of banding marks towards the top half ? :shrug:
- IMG_6308.JPG (256.08 KiB) Viewed 5225 times
EDIT:
ahhh, It looks like the print got incredibly thin towards the top as it is almost transparent looking at it now...
- IMG_6309.JPG (175.58 KiB) Viewed 5222 times
Re: exxos blog - random goings on
Posted: 22 Mar 2021 19:46
by exxos
Finally started to program and test the TOS206 decoder boards... Hopefully these will be in stock again very soon...
- IMG_6310.JPG (332.82 KiB) Viewed 5210 times
Re: exxos blog - random goings on
Posted: 23 Mar 2021 23:11
by exxos
Best Eagle routing ever!
- Capture.PNG (50.75 KiB) Viewed 5163 times
Re: exxos blog - random goings on
Posted: 15 Apr 2021 12:01
by exxos
Why is the last track never has anywhere easy to route :lol: :roll:
- Capture.PNG (65.13 KiB) Viewed 4436 times
Re: exxos blog - random goings on
Posted: 15 Apr 2021 12:04
by Icky
exxos wrote: 15 Apr 2021 12:01
Why is the last track never has anywhere easy to route :lol: :roll:
Because you started from the wrong end :P - couldn't resist.
Re: exxos blog - random goings on
Posted: 15 Apr 2021 12:43
by exxos
Icky wrote: 15 Apr 2021 12:04
Because you started from the wrong end :P - couldn't resist.
:chairsmack: Annoying thing is it was all really nice and neat routed then I realised the chips orientated how I had them, would not fit in the ST :roll: So had to swap things around which made the routing a lot harder work :roll:
Re: exxos blog - random goings on
Posted: 15 Apr 2021 13:07
by exxos
Part 1 done...
- 1772.PNG (50.76 KiB) Viewed 4418 times
Re: exxos blog - random goings on
Posted: 15 Apr 2021 13:30
by Icky
exxos wrote: 15 Apr 2021 13:07
Part 1 done...
If you use those smaller BQ buffer packages we were discussing the other day you could stager the DIPs and make it slimmer similar to the H4 buffer board.
https://www.exxosforum.co.uk/forum/viewt ... 587#p20746