Page 122 of 337
Re: exxos blog - random goings on
Posted: 18 Mar 2021 13:34
by exxos
...and so it begins... if it ends or not is a totally different matter... :lol:
- IMG_6289.JPG (237.53 KiB) Viewed 4025 times
Re: exxos blog - random goings on
Posted: 18 Mar 2021 16:28
by exxos
Yay! just gotta wait for it to all cool down before I start trying to hammer it off the bed!
- IMG_6291.JPG (260.04 KiB) Viewed 4013 times
- IMG_6292.JPG (239.01 KiB) Viewed 4013 times
Re: exxos blog - random goings on
Posted: 18 Mar 2021 16:57
by exxos
As expected, some slight oopsies :roll:
- IMG_6294.JPG (208.69 KiB) Viewed 4006 times
- IMG_6295.JPG (215.66 KiB) Viewed 4006 times
EDIT:
Hacksaw later...
- IMG_6297.JPG (250.96 KiB) Viewed 4001 times
- IMG_6296.JPG (222.96 KiB) Viewed 4001 times
Re: exxos blog - random goings on
Posted: 18 Mar 2021 17:39
by exxos
REV1 on the go...
Tried to cut down on material a bit as took over 3 hours to print!
- Capture.PNG (78.5 KiB) Viewed 3992 times
Re: exxos blog - random goings on
Posted: 18 Mar 2021 18:27
by exxos
Made a bit more progress on the TOS206 boards. Left them on a glass sheet on my hot plate to see if I can get some warmth around them to dry them out quicker.
- IMG_6298.JPG (440.84 KiB) Viewed 3975 times
Re: exxos blog - random goings on
Posted: 18 Mar 2021 21:07
by exxos
Re: exxos blog - random goings on
Posted: 19 Mar 2021 13:42
by exxos
More tweaks...
The slot for the top of the syringe has now been put back, the slots themselves were actually fine, it was the semicircle part of the syringe which was not cut backwards for some odd reason :shrug:
- 2.PNG (95.7 KiB) Viewed 3931 times
I have also taken a chunk out of the bottom part to allow the syringe to go in the holder at an angle easier... Because the top of the syringe now goes in at an angle, I have also angled the top part of the syringe so it should slot in a lot easier now...
- 1.PNG (76.49 KiB) Viewed 3931 times
Re: exxos blog - random goings on
Posted: 22 Mar 2021 13:22
by exxos
REV3 underway.. It is surprisingly strong even at 10% infill...
- IMG_6303.JPG (265.03 KiB) Viewed 3876 times
Re: exxos blog - random goings on
Posted: 22 Mar 2021 14:07
by exxos
Next project... As my printer has 80 mm fans on the back, I want to connect a hose to the back fans. So then the fan pumps out the stink from inside and blows it down the hose which I can throw out of the window...
So thus my fan ducting adapter is born...
- 1.PNG (81.96 KiB) Viewed 3868 times
Re: exxos blog - random goings on
Posted: 22 Mar 2021 15:28
by exxos
This one fits really nice now :)
- IMG_6305.JPG (261.25 KiB) Viewed 3859 times
- IMG_6304.JPG (241.47 KiB) Viewed 3859 times
- IMG_6306.JPG (249.84 KiB) Viewed 3859 times
I guess I don't really need the lug parts to hold the nut..