Page 12 of 21
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 19:08
by Icky
Well done @rubber_jonnie - I will drop an H4 mug into the post for you.
:yay:
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 19:10
by exxos
rubber_jonnie wrote: 05 Mar 2020 19:04
@exxos Well, I put the dot up towards the L/H rear corner of the board (I think there was a * there), is that correct?
Yeah the dot on the chip goes to the * on the board.
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 19:11
by rubber_jonnie
exxos wrote: 05 Mar 2020 19:10
rubber_jonnie wrote: 05 Mar 2020 19:04
@exxos Well, I put the dot up towards the L/H rear corner of the board (I think there was a * there), is that correct?
Yeah the dot on the chip goes to the * on the board.
@exxos Cool, I will remove/rework/etc and see what comes out of it.
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 19:12
by rubber_jonnie
Icky wrote: 05 Mar 2020 19:08
Well done @rubber_jonnie - I will drop an H4 mug into the post for you.
:yay:
@Icky I would make it my preferred beverage conveyance :)
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 21:13
by PaulJ
Ok, @rubber_jonnie you can tell us now how long have you had it running? You were just screwing with @PhilC right. Anyway congrats!! Nice job!! :thumbup: :thumbup: :thumbup:
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 21:28
by PhilC
Hahaha, well good for @rubber_jonnie if he was as he had me fooled if so.
I'm overjoyed to see that RJ has got it up and running as theres nothing quite like seeing a computer youve built spring in to life.
That and now RJ has fixed his H4, he can help break some of the other stuff. This breaking is time consuming hard work.
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 22:49
by rubber_jonnie
@PaulJ Literally had it running since about 17:20 GMT today!
I just had the idea to use the IDE interface to give it a ROM and that did it.
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 22:51
by rubber_jonnie
PhilC wrote: 05 Mar 2020 21:28
Hahaha, well good for @rubber_jonnie if he was as he had me fooled if so.
I'm overjoyed to see that RJ has got it up and running as theres nothing quite like seeing a computer youve built spring in to life.
That and now RJ has fixed his H4, he can help break some of the other stuff. This breaking is time consuming hard work.
I'm overjoyed too
@PhilC!
Now tell me what I can break!
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 22:56
by PaulJ
rubber_jonnie wrote: 05 Mar 2020 22:49
@PaulJ Literally had it running since about 17:20 GMT today!
I just had the idea to use the IDE interface to give it a ROM and that did it.
RJ, we knew you could do it... just need the proper incentive.. :bravo: :bravo: :bravo:
Re: RJ's Attempt. Maybe he's going to finish this time!
Posted: 05 Mar 2020 23:12
by rubber_jonnie
:girldance: :girldance: :girldance: