Page 2 of 21

Re: TF4060 Beta Program

Posted: 14 Jun 2024 18:36
by count
Oh hello,

got mine running today, and I rather like it!

The copperlist effects on boot are still a bit unexpected, it doesn't always boot through entirely yet with my un-adjusted startup-sequence, and on the first go the keyboard didn't work, but probably for unrelated reasons ...

Configuration is:
- A4000+ Mainboard with 68030 populated
- Recapped original PSU, original case
- original Riser board
- ZZ9000 + AX
- Buddha Plus One IDE controller (direct 32GB CF + CDROM + 4GB data transfer CF in reader)
- iKod.se int7 adapter with simple NMI push-button in place of keyboard lock
- Gotek DF0

all of which seems to be working nicely!

still waiting for a 40pin IDE terminator for the mainboard and a 44pin IDE cable to attach a Transcend TS128GPSD330 to the TF4060 directly.

What's not working (and expected not to) is a
- bsc Oktagon 2008 SCSI Controller with ZuluSCSI Mini RP2040

.. which has a quite dated ROM which uses MOVEP instructions unavailable on 060 - should work after I do a ROM upgrade.

My DF1 HD Floppy Drive is broken / badly decalibrated beyond my ability to fix, sadly - if someone has a new one or a good idea I'm happy to hear it.

I'll be fiddling with it, of course, and will have a look at Linux and NetBSD running on it.

Thanks for the awesome work!!!

count

Re: TF4060 Beta Program

Posted: 14 Jun 2024 20:20
by terriblefire
Thanks for the report. it's not a copperlist it's just a counter hitting colour0. Exactly the same code as in most of my cards

Re: TF4060 Beta Program

Posted: 23 Jun 2024 19:12
by kludge
Is it possible to get a drawing/dimensions for the heat sink mounting holes relative to the CPU, @terriblefire ? I could probably get close enough with calipers, but your measurments would be exact πŸ˜„

Re: TF4060 Beta Program

Posted: 26 Jun 2024 12:46
by terriblefire
kludge wrote: 23 Jun 2024 19:12 Is it possible to get a drawing/dimensions for the heat sink mounting holes relative to the CPU, @terriblefire ? I could probably get close enough with calipers, but your measurments would be exact πŸ˜„
Yes i'll see what i can do

Re: TF4060 Beta Program

Posted: 02 Jul 2024 13:05
by kludge
kludge wrote: 23 Jun 2024 19:12 Is it possible to get a drawing/dimensions for the heat sink mounting holes relative to the CPU, @terriblefire ? I could probably get close enough with calipers, but your measurments would be exact πŸ˜„
Not perfect, but close enough for now I think!

Reamiga 4000CR w/ 64 MB RAM hack, CyberVision 64/3D, FastLane SCSI Z3, Kickstart 3.2.2. At least it boots to the Kickstart screen. Will test more later.

tf4060heatsink1.jpg
tf4060heatsink1.jpg (133.52 KiB) Viewed 1504 times
tf4060heatsink2.jpg
tf4060heatsink2.jpg (153.46 KiB) Viewed 1504 times
tf4060heatsink3.jpg
tf4060heatsink3.jpg (211.88 KiB) Viewed 1504 times
'
tf4060heatsink4.jpg
tf4060heatsink4.jpg (162.86 KiB) Viewed 1504 times

Re: TF4060 Beta Program

Posted: 02 Jul 2024 14:52
by alexh
Looks interesting. Is this an off the shelf heatsink with good availability?

I wonder what it is like for clearance in A3000? They have far less room above CPU card than A4000.

Re: TF4060 Beta Program

Posted: 02 Jul 2024 15:50
by kludge
alexh wrote: 02 Jul 2024 14:52 Looks interesting. Is this an off the shelf heatsink with good availability?

I wonder what it is like for clearance in A3000? They have far less room above CPU card than A4000.
Sadly I have no idea where that heatsink came from. I’ve had it for years. But the design could be adapted to other heatsinks, I’m sure.

I don’t have a 3000 to test with either.

Re: TF4060 Beta Program

Posted: 03 Jul 2024 11:51
by terriblefire
terriblefire wrote: 26 Jun 2024 12:46
kludge wrote: 23 Jun 2024 19:12 Is it possible to get a drawing/dimensions for the heat sink mounting holes relative to the CPU, @terriblefire ? I could probably get close enough with calipers, but your measurments would be exact πŸ˜„
Yes i'll see what i can do
Drill file attached - T10 is the CPU holder drills i think .

Drill File Info:

Data Mode : Absolute
Units : 1/100000 Inch

Drills used:

Code Size used

T01 0.0120inch 293
T02 0.0138inch 367
T03 0.0276inch 1
T04 0.0315inch 422
T05 0.0354inch 44
T06 0.0394inch 42
T07 0.0400inch 30
T08 0.0520inch 3
T09 0.0930inch 2
T10 0.1000inch 5
T11 0.1575inch 3

Total number of drills: 1212

Code: Select all

T10
X594944Y92977
X601003Y182884
X383535Y98104
X354868Y182746
X383535Y273634
Also pushed to terriblefire-binaries.

tf4060.TXT
(17.48 KiB) Downloaded 53 times

Re: TF4060 Beta Program

Posted: 03 Jul 2024 13:05
by kludge
terriblefire wrote: 03 Jul 2024 11:51 Drill file attached - T10 is the CPU holder drills i think .
Something like this, if I didn't make a typo somewhere

TF4060 rev 5 heatsink mounting holes.png
TF4060 rev 5 heatsink mounting holes.png (448.97 KiB) Viewed 1368 times

Re: TF4060 Beta Program

Posted: 04 Jul 2024 17:42
by gurrag
kludge wrote: 02 Jul 2024 13:05
kludge wrote: 23 Jun 2024 19:12 Is it possible to get a drawing/dimensions for the heat sink mounting holes relative to the CPU, @terriblefire ? I could probably get close enough with calipers, but your measurments would be exact πŸ˜„
Not perfect, but close enough for now I think!

Reamiga 4000CR w/ 64 MB RAM hack, CyberVision 64/3D, FastLane SCSI Z3, Kickstart 3.2.2. At least it boots to the Kickstart screen. Will test more later.


tf4060heatsink1.jpg

tf4060heatsink2.jpg

tf4060heatsink3.jpg
'
tf4060heatsink4.jpg
hello do you have an stl availiable ?
would like to try this out :)