Page 2 of 26
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 19:53
by Cego
terriblefire wrote: 17 Dec 2021 19:27
Cego wrote: 17 Dec 2021 19:20
67 setting in cpuspeed will result in a freeze on my machine. So far 84 and 50 works stable (didnt go higher)
Throughout testing 94 was seen as the best speed
i see, but honestly thats to much for my needs (dont want to stress the CPU and CPLDs). I am happy with 66MHz as all demos will just run fine :)
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 19:57
by terriblefire
PaulJ_2.0 wrote: 17 Dec 2021 19:46
I'm getting nothing from the new firmware on my Rev 2B.
LED power stays dim.
If I revert to previous beta 2021_09_07_999 it's booting fine.
Strange this motherboard...
Been tested on 3 rev 2s. Infact rev2B was the most stable platform.
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:01
by chucky
(as 8bitbubsy didnt get any activationmail he mailed me)
Message (from 8bitbubsy):
I got the firmware flashed today, using a Rasberry Pi 4 + xcs3prog. Had to disconnect 3.3v from the Pi and power up the Amiga with the board connected.
It seems to run fine, here are my bustest speeds:
tf1260_new_fw.jpg
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:02
by PaulJ_2.0
terriblefire wrote: 17 Dec 2021 19:57
Been tested on 3 rev 2s. Infact rev2B was the most stable platform.
I'm not sure what it can be. It's not got anything other than a gotek in it.
All timing fixes are present and correct and it's perfectly stable and checks out fine 99.9% of the time. The odd firmware update and it refuses to init.
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:09
by supaduper
PaulJ_2.0 wrote: 17 Dec 2021 20:02
terriblefire wrote: 17 Dec 2021 19:57
Been tested on 3 rev 2s. Infact rev2B was the most stable platform.
I'm not sure what it can be. It's not got anything other than a gotek in it.
All timing fixes are present and correct and it's perfectly stable and checks out fine 99.9% of the time. The odd firmware update and it refuses to init.
With no boot device on the A1200 does it go to the insert floppy rom screen ?
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:10
by chucky
After 30ish seconds. (powerled should go to fullbright after 1 sec)
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:18
by PaulJ_2.0
supaduper wrote: 17 Dec 2021 20:09
With no boot device on the A1200 does it go to the insert floppy rom screen ?
PaulJ_2.0 wrote: 17 Dec 2021 19:46
LED power stays dim.
It doesn't even start to initialise.
Even Diagrom wont start.
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:24
by supaduper
PaulJ_2.0 wrote: 17 Dec 2021 20:18
supaduper wrote: 17 Dec 2021 20:09
With no boot device on the A1200 does it go to the insert floppy rom screen ?
PaulJ_2.0 wrote: 17 Dec 2021 19:46
LED power stays dim.
It doesn't even start to initilise.
any difference if you wait say 40 to 50 seconds before trying to power on again ?
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:26
by PaulJ_2.0
supaduper wrote: 17 Dec 2021 20:24
any difference if you wait say 40 to 50 seconds before trying to power on again ?
No, the power stays dim at all times, cold or warm reset.
Same with Diagrom installed, nothing initialises, power just sits at dim.
Re: TF1260 New Firmware Alpha Released!
Posted: 17 Dec 2021 20:31
by supaduper
PaulJ_2.0 wrote: 17 Dec 2021 20:26
supaduper wrote: 17 Dec 2021 20:24
any difference if you wait say 40 to 50 seconds before trying to power on again ?
No, the power stays dim at all times, cold or warm reset.
Same with Diagrom installed, nothing initialises, power just sits at dim.
You can send back to me to test that way we can eliminate either the Card or your A1200