Added!
You will not be able to post if you are still using Microsoft email addresses such as Hotmail etc
See here for more information viewtopic.php?f=20&t=7296
See here for more information viewtopic.php?f=20&t=7296
BOOKMARK THIS PAGE !
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
DO NOT USE MOBILE / CGNAT DEVICES WHERE THE IP CHANGES CONSTANTLY!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
H5 BUYERS INTERESTS
-
exxos
- Site Admin
- Posts: 28093
- Joined: 16 Aug 2017 23:19
- Location: UK
-
arkadiusz.makarenko
- Moderator Team
- Posts: 1360
- Joined: 19 Jun 2019 07:36
- Location: Edinburgh
Re: H5 BUYERS INTERESTS
I would like to get one, please.
Do not trust people. They are capable of greatness.
~ Stanislaw Lem
~ Stanislaw Lem
-
exxos
- Site Admin
- Posts: 28093
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: H5 BUYERS INTERESTS
Added!
-
ube
- Posts: 143
- Joined: 21 Aug 2017 11:34
-
DoG
- Posts: 1286
- Joined: 07 Apr 2018 12:26
Re: H5 BUYERS INTERESTS
Better jump on this before the limit cap is set ;)
BTW, since this time it's SMT, is the pre assembly board of caps/res going to take that long? Is pre-ass/bare coming in the same package? I mean, I can go either way. I can solder in all those my self, but rather not. I get that is was more of a special order last time considering all was hand soldered and this time it's a pick-n-place job. I am sure some want all the sockets and as much pre soldered they can get. Enough rant...
I take one PCB with pre assembly of caps/res, if it arrives about the same time. Otherwise a bare PCB, thanks.
BTW, since this time it's SMT, is the pre assembly board of caps/res going to take that long? Is pre-ass/bare coming in the same package? I mean, I can go either way. I can solder in all those my self, but rather not. I get that is was more of a special order last time considering all was hand soldered and this time it's a pick-n-place job. I am sure some want all the sockets and as much pre soldered they can get. Enough rant...
I take one PCB with pre assembly of caps/res, if it arrives about the same time. Otherwise a bare PCB, thanks.
-
exxos
- Site Admin
- Posts: 28093
- Joined: 16 Aug 2017 23:19
- Location: UK
Re: H5 BUYERS INTERESTS
@ube Added!
@DoG Added!
@DoG The SMT generic parts will be assembled at the factory along with the PCBs. The delay last time was because of the PCBs was sent to a UK company to assemble the SMT and through hole. All other parts will remain soldered by the buyer.
@DoG Added!
@DoG The SMT generic parts will be assembled at the factory along with the PCBs. The delay last time was because of the PCBs was sent to a UK company to assemble the SMT and through hole. All other parts will remain soldered by the buyer.
-
DoG
- Posts: 1286
- Joined: 07 Apr 2018 12:26
Re: H5 BUYERS INTERESTS
Great! :dualthumbup:exxos wrote: 21 May 2020 21:10...
@DoG The SMT generic parts will be assembled at the factory along with the PCBs. The delay last time was because of the PCBs was sent to a UK company to assemble the SMT and through hole. All other parts will remain soldered by the buyer.
-
PhilC
- Moderator
- Posts: 7370
- Joined: 23 Mar 2018 20:22
Re: H5 BUYERS INTERESTS
I'd recommend most to get the boards with the pressssembled smt components. It'll save so much time in self assembly and shopping for parts.
Even though I've now built 2 Alpha boards and 3 H4 boards I'd get mine preassembled with the smt stuff leaving the easier stuff for after. And let's face it, a machine can solder surface mount stuff far better and faster than I can.
Even though I've now built 2 Alpha boards and 3 H4 boards I'd get mine preassembled with the smt stuff leaving the easier stuff for after. And let's face it, a machine can solder surface mount stuff far better and faster than I can.
If it ain't broke, test it to Destruction.
-
Icky
- Site Admin
- Posts: 4311
- Joined: 03 Sep 2017 10:57
- Location: UK
Re: H5 BUYERS INTERESTS
I agree @PhilC. I build boards all the time (have a few SMT ones this weekend to do). I would much rather have the board supplied with all the SMT work done as it will save time and effort which I can use elsewhere :)PhilC wrote: 21 May 2020 21:15 I'd recommend most to get the boards with the pressssembled smt components. It'll save so much time in self assembly and shopping for parts.
Even though I've now built 2 Alpha boards and 3 H4 boards I'd get mine preassembled with the smt stuff leaving the easier stuff for after. And let's face it, a machine can solder surface mount stuff far better and faster than I can.
-
philbo34
- Site sponsor
- Posts: 200
- Joined: 21 Apr 2020 10:46
Re: H5 BUYERS INTERESTS
ill take 1 please.
cheers
cheers
Who is online
Users browsing this forum: CCBot and 0 guests