You will not be able to post if you are still using Microsoft email addresses such as Hotmail etc
See here for more information viewtopic.php?f=20&t=7296
BOOKMARK THIS PAGE !
https://www.exxosforum.co.uk:8085/IP_CHECK/
You can unban yourself if needed. It also sends me reports to investigate the ban.
DO NOT USE MOBILE / CGNAT DEVICES WHERE THE IP CHANGES CONSTANTLY!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!

Robson’s

Topic for users to share their building progress.
User avatar
Robson
Posts: 143
Joined: 13 May 2020 16:22

Re: Robson’s

Post by Robson »

The DMA fix board arrived thanks to @DoG and it's now installed.

I've also done the 1.44 mod and installed the gotek as described here:
https://exxosforum.co.uk/forum/viewtopic.php?f=78&t=2551

The bootloader comes on but after displaying the fw version I get the Error: LBA change Test Failed! Write Issue? message.

It works when I set everything back to default.

Any ideas?
IMG_7151.JPG
You do not have the required permissions to view the files attached to this post.
Top
User avatar
kodak80
Posts: 524
Joined: 21 Oct 2017 01:14
Location: Brisbane, QLD, Australia

Re: Robson’s

Post by kodak80 »

I don't believe that this issue was resolved and might be worth asking on the FF Github pages.

I don't use the HxC Autoboot HFE tool. Instead, I use and OLED and then use the Gotek buttons to load disk images.
Raven060 | Atari Falcon 030 | Atari 1040 STE | Atari 1040 STFM | Atari 1040 STF | Kryoflux & Supercard Pro Flux boards
Creator of the Atari ST Review magazine archive: https://www.chillichai.com/atari-st-review
Top
User avatar
Robson
Posts: 143
Joined: 13 May 2020 16:22

Re: Robson’s

Post by Robson »

IDE is now working. The DMA fix slightly pushes the DOM up. I'll lower it at some point.

IMG_7220.JPG
IMG_7218.JPG
IMG_7215.JPG
You do not have the required permissions to view the files attached to this post.
Top
User avatar
Icky
Site Admin
Site Admin
Posts: 4311
Joined: 03 Sep 2017 10:57
Location: UK

Re: Robson’s

Post by Icky »

Nice. Another H4 and IDE working :thumbup:
Top
User avatar
Robson
Posts: 143
Joined: 13 May 2020 16:22

Re: Robson’s

Post by Robson »

Forgot to add a socket for this upgrade.
BA12F2D5-4C4E-4555-8E0D-7B4D405ED8EB.jpg
You do not have the required permissions to view the files attached to this post.
Top
User avatar
derkom
Moderator
Moderator
Posts: 1230
Joined: 29 Jul 2018 18:45

Re: Robson’s

Post by derkom »

Robson wrote: 14 Jun 2020 15:24 Forgot to add a socket for this upgrade
No need. You were born with one.
Top
User avatar
Robson
Posts: 143
Joined: 13 May 2020 16:22

Re: Robson’s

Post by Robson »

A growing collection.
IMG_7252.JPG
You do not have the required permissions to view the files attached to this post.
Top
User avatar
Robson
Posts: 143
Joined: 13 May 2020 16:22

Re: Robson’s

Post by Robson »

Board nr2 that I bought from @Velociraptor.
I was going for it, this is all built today. Only few things left but run out of sockets so will fully complete the board when they're here.

104879810_10160380223137715_3172571423607197759_n.jpg
You do not have the required permissions to view the files attached to this post.
Top
User avatar
exxos
Site Admin
Site Admin
Posts: 28092
Joined: 16 Aug 2017 23:19
Location: UK

Re: Robson’s

Post by exxos »

Pretty impresses amount of stuff added in just a day! :thumbup:
Top
User avatar
Robson
Posts: 143
Joined: 13 May 2020 16:22

Re: Robson’s

Post by Robson »

After a little bit of sizzling that's cured with IPA bath + drying Board Nr2 is alive.
IMG_7331.JPG
You do not have the required permissions to view the files attached to this post.
Top

Return to “MONGREL H4 USER BUILDS”

Who is online

Users browsing this forum: No registered users and 0 guests