Yikes i hope its not gone missing.
You will not be able to post if you are still using Microsoft email addresses such as Hotmail etc
See here for more information viewtopic.php?f=20&t=7296
See here for more information viewtopic.php?f=20&t=7296
DO NOT USE MOBILE / CGNAT DEVICES WHERE THE IP CHANGES CONSTANTLY!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
At this time, it is unfortunately not possible to whitelist users when your IP changes constantly.
You may inadvertently get banned because a previous attack may have used the IP you are now on.
So I suggest people only use fixed IP address devices until I can think of a solution for this problem!
Please make sure you are logged in for at least 2 hours
to make sure your IP is added into the firewall whitelist, thanks
to make sure your IP is added into the firewall whitelist, thanks
TF536 Rev 2 Design Complete (all gone)
Moderators: terriblefire, Terriblefire Moderator
-
terriblefire
- Admin sponsor
- Posts: 5675
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF536 Rev 2 Design Complete (all gone)
Nah, it's the COVID. The mail is reaaaally slow now, in fact I have now switched to shipping everything via UPS.
-
terriblefire
- Admin sponsor
- Posts: 5675
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
Mail here is not affected. Getting stuff from Spain in two days.alenppc wrote: Fri May 01, 2020 6:19 pm Nah, it's the COVID. The mail is reaaaally slow now, in fact I have now switched to shipping everything via UPS.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: TF536 Rev 2 Design Complete (all gone)
Yea mate covid mail, it is on the slow boat, had to wait near on 6 weeks for some memory to reach OZ from the UK, hopefully your card is on a speed boat to Canada
Life is really simple, but we insist on making it complicated - Confucius
Re: TF536 Rev 2 Design Complete (all gone)
I can confirm buffered ide works fine with pin1 lifted and tied to pin2 on IC6.
Thanks Stephen
Thanks Stephen
-
LADmachining
- Posts: 41
- Joined: Sun Mar 24, 2019 2:19 pm
Re: TF536 Rev 2 Design Complete (all gone)
I seem to have an open circuit in the board as I have no connection between the STERM CPU pin and any pin on the CPLD. Pins adjacent to STERM such as BERR and DSACK1 do find their way back to the CPLD.
On unpacking the board when received, it had a scuff in the solder mask in this area and between the 68K pads. Checking over with the microscope before assembly did not reveal any open circuits, but I guess there was something that was missed.
Could a schematic or boardview file be made available to assist with tracking down the fault? Thanks!
On unpacking the board when received, it had a scuff in the solder mask in this area and between the 68K pads. Checking over with the microscope before assembly did not reveal any open circuits, but I guess there was something that was missed.
Could a schematic or boardview file be made available to assist with tracking down the fault? Thanks!
-
terriblefire
- Admin sponsor
- Posts: 5675
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
I'll do one for you now.. need a beer first.LADmachining wrote: Sun May 03, 2020 10:16 am Could a schematic or boardview file be made available to assist with tracking down the fault? Thanks!
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
LADmachining
- Posts: 41
- Joined: Sun Mar 24, 2019 2:19 pm
Re: TF536 Rev 2 Design Complete (all gone)
Don't blame you - deserved after completing the Harlequin build!
-
terriblefire
- Admin sponsor
- Posts: 5675
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: TF536 Rev 2 Design Complete (all gone)
OBV file
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
-
LADmachining
- Posts: 41
- Joined: Sun Mar 24, 2019 2:19 pm
Re: TF536 Rev 2 Design Complete (all gone)
Thanks. Will dig into the board a bit later and hopefully get to the bottom of the issue.
Anthony
Anthony