@terriblefire - Go for the smt route for caps and resistors on the build. I know it's over the through hole component holes but it was so much nicer to build and quicker. I used mostly 0805s but there were a few 33R clock line resistors that where 1206s to span properly. Unfortunately there are a few points where the span is too long and had to go back to the through hole resistors. https://www.exxosforum.co.uk/forum/viewt ... =90#p36700
Can all registered uses please login, even just for a few minutes..
It helps build a picture where our "good traffic" is coming from..
Thanks :)
It helps build a picture where our "good traffic" is coming from..
Thanks :)
H4 BUYERS INTEREST - SOLD OUT!
Re: H4 BUYERS INTEREST
Re: H4 BUYERS INTEREST
And now there is 2.... Everyone start panic buying! 
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: H4 BUYERS INTEREST
Pretty sure the last 2 will go when i start building on stream.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: H4 BUYERS INTEREST
@terriblefire It will be good to know when that will be!
@exxos When those 2 have gone, will you be considering another batch or the next iteration?
@exxos When those 2 have gone, will you be considering another batch or the next iteration?
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: H4 BUYERS INTEREST
I have a CD32 clone from Germany to debug first.
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
Re: H4 BUYERS INTEREST
Next board will have more SMT caps and resistors.. @Icky already swapped those a few weeks ago...I did all the fixes ages ago...JezC wrote: Wed May 13, 2020 4:06 pm @exxos When those 2 have gone, will you be considering another batch or the next iteration?
The only change I am contemplating otherwise is making the flashy clock socket a 3.3V bus.. And maybe putting a additional socket to the left of it
Re: H4 BUYERS INTEREST
That extra socket would make @PhilC buy even more socketsexxos wrote: Wed May 13, 2020 4:18 pm The only change I am contemplating otherwise is making the flashy clock socket a 3.3V bus.. And maybe putting a additional socket to the left of it
Re: H4 BUYERS INTEREST
No problem, would be good to watch & learn from someone who knows what they are doing!
Re: H4 BUYERS INTEREST
Maybe we should have a private betting pool as to how many times terriblefire complains about somethingJezC wrote: Wed May 13, 2020 4:22 pmNo problem, would be good to watch & learn from someone who knows what they are doing!
-
terriblefire
- Admin sponsor
- Posts: 5687
- Joined: Mon Aug 28, 2017 10:56 pm
- Location: Glasgow, UK
Re: H4 BUYERS INTEREST
If things were perfect i'd never be motivated to make them better.exxos wrote: Wed May 13, 2020 4:35 pm Maybe we should have a private betting pool as to how many times terriblefire complains about something
———
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."
"It is not necessarily a supply voltage at no load, but the amount of current it can provide when touched that
indicates how much hurting you shall receive."