Am liking the black look of the new Rigol oscilloscopes

Post by **Icky** » Sun Dec 22, 2019 2:40 pm

The new range of Rigol oscilloscopes MSO5000 range look pretty cool in black

: MSO5072-5T.jpg (28.05 KiB) Viewed 5132 times

https://www.rigol-uk.co.uk/Rigol-MSO507 ... so5072.htm

Post by **PhilC** » Sun Dec 22, 2019 2:42 pm

They do look good in black and with 4 channels and an LA built in by the looks.

PaulJ · Post by **PaulJ** » Sun Dec 22, 2019 2:48 pm

Looks pretty nice but there not giving it away either.

Post by **exxos** » Sun Dec 22, 2019 2:50 pm

Didn't Dave Jones review one of those a while back ? I think they were moving to FPGA driven scopes which seemed to be a bit buggy and lacking in some features IIRC.

I need a 4chan scope with a LA built in really, but been a bit puff off Rigol lately as my scope is miss behaving. Could do with more resolution and sample memory than I currently have as well.

Post by **terriblefire** » Sun Dec 22, 2019 2:54 pm

exxos wrote: Sun Dec 22, 2019 2:50 pm Didn't Dave Jones review one of those a while back ? I think they were moving to FPGA driven scopes which seemed to be a bit buggy and lacking in some features IIRC.

I need a 4chan scope with a LA built in really, but been a bit puff off Rigol lately as my scope is miss behaving. Could do with more resolution and sample memory than I currently have as well.

I'd always go for an old HP rather than new cheap ass chinese crap. Just my opinion though. Might be fine.

Post by **exxos** » Sun Dec 22, 2019 3:06 pm

I would prefer oldskool stuff.. Though my scope ends up balancing on top of all the junk in a half open drawer as I have nowhere else to put it

Post by **terriblefire** » Sun Dec 22, 2019 3:08 pm

exxos wrote: Sun Dec 22, 2019 3:06 pm I would prefer oldskool stuff.. Though my scope ends up balancing on top of all the junk in a half open drawer as I have nowhere else to put it

Get a good old HP then everything else can stack on top of it no probs.

Post by **exxos** » Sun Dec 22, 2019 3:14 pm

terriblefire wrote: Sun Dec 22, 2019 3:08 pm
Get a good old HP then everything else can stack on top of it no probs.

I don't have anywhere to put it. https://www.exxosforum.co.uk/forum/viewt ... 164#p26465 pulling that middle drawer out is where I have to balance my scope.

Post by **terriblefire** » Sun Dec 22, 2019 3:17 pm

exxos wrote: Sun Dec 22, 2019 3:14 pm I don't have anywhere to put it. https://www.exxosforum.co.uk/forum/viewt ... 164#p26465 pulling that middle drawer out is where I have to balance my scope.

Under the printer dude.. you got loads of room.

Post by **exxos** » Sun Dec 22, 2019 3:33 pm

Printer is bigger and heavier than it looks.. The whole top flips up to get inside it and I need the physical head room as well to get at the back. I also have to be able to see stuff from my chair as well. So the scope ends up balancing between the draw and little table at a angle. Will take a pic tomorrow to show what I mean. I have given it all a lot of thought , other than moving one of the printers out, its just not doable I think

exxos's Atari, Amiga & retro forum

Am liking the black look of the new Rigol oscilloscopes

Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes

Re: Am liking the black look of the new Rigol oscilloscopes