16MHz Mod PCB install

Related information and WIP etc
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

16MHz Mod PCB install

Post by exxos »

I started a new thread for the install of the Alpha mod PCB..


STEP 1

Cut the DE track as shown below...

Solder a wire approx 4" as shown below.

(note to self, DE from GLUE also goes to MFP... ?)

IMG_4263.JPG
IMG_4263.JPG (289.78 KiB) Viewed 4977 times


STEP 2

Solder a wire as shown (about 8" length)

IMG_4262.JPG
IMG_4262.JPG (300.15 KiB) Viewed 5000 times


STEP 3

Lift the "top side" of the resistors as shown, bend upwards and solder some wires on (about 5" length)

IMG_4264.JPG
IMG_4264.JPG (342.8 KiB) Viewed 4997 times


STEP 4

Unsolder SJ5 and solder a new wire as shown below to R911 (about 5" long)

NOTE: There are 2 wires going to R911 (one is not yet connected to anything as will go to the mod pcb later)

IMG_4266.JPG
IMG_4266.JPG (274.07 KiB) Viewed 4992 times

VIEW FROM ABOVE OF THE LINK WIRE (R923 TO R911)
(I highlighted the wire with a thick red line)

IMG_4267.JPG
IMG_4267.JPG (332.71 KiB) Viewed 4990 times
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: 16MHz Mod PCB install

Post by exxos »

STEP 5

Lift the ends of the resistors as shown.

The free end of R905 needs 2 wires.. 3" and 10" approx.

IMG_4269.JPG
IMG_4269.JPG (244.31 KiB) Viewed 4980 times
IMG_4270.JPG
IMG_4270.JPG (282.92 KiB) Viewed 4980 times


R905 3" wire solders to the free end of R903 as highlighted in red..


IMG_4271.JPG
IMG_4271.JPG (325.47 KiB) Viewed 4980 times

The 10" wire on R905 will solder to the mod pcb later..


(I am not at home again until Monday now.. so will start on the PCB then)
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: 16MHz Mod PCB install

Post by exxos »

STEP 6

Remove IC900 & R910.

Wire link left pad of R910 to left pad of R914.

5" wire from the above wire link (or left pad of R910). This wire will go to the mod PCB later.

IMG_4272.JPG
IMG_4272.JPG (447.04 KiB) Viewed 4921 times
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: 16MHz Mod PCB install

Post by exxos »

STEP 7

All resistors on the PCB are 0805 33R unless otherwise stated.

The 68R is a regulator 1/8w resistor which solders to the 8MHz mod pad. The free end goes to the long wire which links up the 1772 etc.

8MHz points shown in the image below.

IMG_4280.JPG
IMG_4280.JPG (463.41 KiB) Viewed 4911 times
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: 16MHz Mod PCB install

Post by exxos »

STEP 8

47pF from the 16MHz pad to GND.. There seems to be a lot of under and overshoot on the 16MHz. So the capacitor helps smooth the signal out. I do not believe this is actually necessary for operation, but I do recommend fitting it..

I highlighted in red the link wire between the blitter and CPU wire ( of course this wire should have already been done in the above steps anyway)

1.jpg
1.jpg (470.35 KiB) Viewed 4908 times



STEP 9

Wire 5V and 0V to the PCB.

The support wire is there is something to anchor the PCB down a little bit.

2.jpg
2.jpg (461.75 KiB) Viewed 4907 times



STEP 10

2MHz white wire link..

3.jpg
3.jpg (455.87 KiB) Viewed 4906 times
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: 16MHz Mod PCB install

Post by exxos »

STEP 11


RED arrows show one wire. From the mod PCB to near the SIL array (GLUE DE from step 1)

The BLUE arrow is the wire which goes under the RAM board (MMU DE from step 2)

4.jpg
4.jpg (505.99 KiB) Viewed 4904 times


STEP 12

32MHz wire (done from step 6)
IMG_4279.JPG
IMG_4279.JPG (510.21 KiB) Viewed 4904 times
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: 16MHz Mod PCB install

Post by exxos »

So off you all go now then! :lol: The race is on...

I think my guide seriously sucks, and I think it looks way more complicated than it actually is :roll:

If anyone needs any more images, or clarifications, then post below and I will take some more images will explain anything any better if needs be....


EDIT:

Due to issues found here https://www.exxosforum.co.uk/forum/viewt ... 941#p22938

Likely the power will have to be cycled a couple of times to get it in a wake up state which works (must leave 10 seconds off before turning back on again).
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
User avatar
rubber_jonnie
Site Admin
Site Admin
Posts: 10472
Joined: Thu Aug 17, 2017 7:40 pm
Location: Essex
Contact:

Re: 16MHz Mod PCB install

Post by rubber_jonnie »

Holy cheesy nachos Batman!!
Collector of many retro things!
800XL and 65XE both with Ultimate1MB,VBXL/XE & PokeyMax, SIDE3, SDrive Max, 2x 1010 cassette, 2x 1050 one with Happy mod, 3x 2600 Jr, 7800 and Lynx II
Approx 20 STs, including a 520 STM, 520 STFMs, 3x Mega ST, MSTE & 2x 32 Mhz boosted STEs
Plus the rest, totalling around 50 machines including a QL, 3x BBC Model B, Electron, Spectrums, ZX81 etc...
User avatar
Icky
Site Admin
Site Admin
Posts: 3986
Joined: Sun Sep 03, 2017 10:57 am
Location: UK

Re: 16MHz Mod PCB install

Post by Icky »

exxos wrote: Mon Jun 03, 2019 2:12 pm So off you all go now then! :lol: The race is on...

I think my guide seriously sucks, and I think it looks way more complicated than it actually is :roll:

If anyone needs any more images, or clarifications, then post below and I will take some more images will explain anything any better if needs be....
Great work exxos.

It is a simple design but to get there takes a lot of wires. It's essentially re-creating new bus lines with wires and circumventing the original lines. I should have my ocd header / jumper wire version working later tonight - fingers crossed.

Only observation I have is be careful soldering to the vias for the DE lines. In moving my board yesterday I caught the wire and it pulled up the track on the top side of the board. Fortunately that track is not needed as we cut it.
User avatar
exxos
Site Admin
Site Admin
Posts: 23499
Joined: Wed Aug 16, 2017 11:19 pm
Location: UK
Contact:

Re: 16MHz Mod PCB install

Post by exxos »

Icky wrote: Mon Jun 03, 2019 6:46 pm It is a simple design but to get there takes a lot of wires. It's essentially re-creating new bus lines with wires and circumventing the original lines. I should have my ocd header / jumper wire version working later tonight - fingers crossed.
Yeah, but even so, its a whole lot easier than the STFM, as the remake has all clock lines going via resistors to allow this mod to be done "easily". On a real STFM.. it be a whole epic of track cutting and patching.
Icky wrote: Mon Jun 03, 2019 6:46 pm Only observation I have is be careful soldering to the vias for the DE lines. In moving my board yesterday I caught the wire and it pulled up the track on the top side of the board. Fortunately that track is not needed as we cut it.
If your soldering to the top of the pad then yes, the tracks are tiny and can rip off easily. Though I use tiny wire which solders into the via, so its pretty solid really.
https://www.exxosforum.co.uk/atari/ All my hardware guides - mods - games - STOS
https://www.exxosforum.co.uk/atari/store2/ - All my hardware mods for sale - Please help support by making a purchase.
viewtopic.php?f=17&t=1585 Have you done the Mandatory Fixes ?
Just because a lot of people agree on something, doesn't make it a fact. ~exxos ~
People should find solutions to problems, not find problems with solutions.
Post Reply

Return to “H4 MONGREL EDITION DEVELOPMENT & INFO”